Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Nordic SDK: swapping LEDS_ON and LEDS_OFF caused problem when checking if the LEDS are on 0

I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
- s120
- gpio
- sdk8.1
- nrf51822
743 views

0 replies

Started over 8 years ago
by tyler
Not Answered

Ble connection details not showing up in wireshark 0

Hello, I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...

713 views

0 replies

Started over 8 years ago
by Newbie
Not Answered

[bug report & fix] app_uart_fifo is sending APP_UART_TX_EMPTY event before the last byte is sent 0

Hi Team, We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...

1870 views

0 replies

Started over 8 years ago
by Patrice Rudaz
Not Answered
Pairing procedure failed by bonding 0

Hello everybody, for my project, i will bond the peripherial with the central. I test my device with the MCP and can connect without problems. When i press the Bond Button...
- bond
- sdk11
- s132
- nrf52832
1278 views

0 replies

Started over 8 years ago
by 1_andi
Not Answered
nRF52 max. input frequency on GPIO 0

Hi all, I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
- 132 nrf52832 gpio
2093 views

0 replies

Started over 8 years ago
by Pascal Künzi

Recent in Nordic blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015