Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

OpenOCD with nRF52 and Olimex debugger 0

I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...

2355 views

0 replies

Started over 8 years ago
by Tosa
Not Answered

nRF24LE1 (multiple) to nRF24L01 (1) sample RF projects? 0

Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...

1359 views

0 replies

Started over 8 years ago
by mr_creosote
Not Answered

task time of radio from DISABLE to RX 0

HI: i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow: while (1) { Rf_StartRx(ReciverSC.RfBufPointer...

577 views

0 replies

Started over 8 years ago
by baicai
Not Answered

nrf51822 and tmp102 0

Hi to everyone, i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822. I want to read the values of the sensor over a beacon app. ...

602 views

0 replies

Started over 8 years ago
by Roberto
Not Answered

After DFU, the device can't reset 0

Hi,I'm glad you can see my post. Now, I am in a program to read and write FLASH such as the screenshot in the attachment. Then I update with DFU service for the equipment...

781 views

0 replies

Started over 8 years ago
by ymYin

Recent in Nordic blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015