Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Impossible to debug or flash the examples with IAR & CMSIS-DAP 0

Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...

1272 views

0 replies

Started over 8 years ago
by agf
Not Answered
Ble Mesh and advertising 0

Hi, What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board When i download the app,why doesnt advertising exist.i cant...
- advertising
- mesh
983 views

0 replies

Started over 8 years ago
by Oguz Emre
Not Answered
Library for NRF905 on Raspberry Pi 0

Hi all, Is there any stable library for NRF905 on Raspberry Pi? Thanks and Regards, Wonderful IOT
- nrf905 raspberry pi library
2568 views

0 replies

Started over 8 years ago
by Wonderful IOT
Not Answered

How to know the master is iOS or android? 0

How to know the master is iOS or Android when nRF51/52 is advertising or connected?

464 views

0 replies

Started over 8 years ago
by efengzu
Not Answered
Nrf5 IoT sdk Warning issue 0

hello i am using the Nrf52dk with Visualgdb. i try to run the example project (tcp/IP -> client). i am using the Nrf5 IoT sdk v0.9 Project complied successfully but i...
- nrf52
- iot
748 views

0 replies

Started over 8 years ago
by All4here

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019