Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nrf51822 and tmp102 0

Hi to everyone, i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822. I want to read the values of the sensor over a beacon app. ...

579 views

0 replies

Started over 8 years ago
by Roberto
Not Answered

After DFU, the device can't reset 0

Hi,I'm glad you can see my post. Now, I am in a program to read and write FLASH such as the screenshot in the attachment. Then I update with DFU service for the equipment...

754 views

0 replies

Started over 8 years ago
by ymYin
Not Answered
Master Control Panel - Change MTU size 0

Hi Is it possible to change the MTU size with the Master Control Panel? I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
- mtu
1502 views

0 replies

Started over 8 years ago
by cp52
Not Answered
can anybody share a battery_level_in_percent for AA battery? 0

Is there a function like battery_level_in_percent for AA battery? I know battery_level_in_percent is only for CR2032. Even though I compensate it to make it 3V from AA battery...
- battery level
- adc
1084 views

0 replies

Started over 8 years ago
by sosse
Not Answered
Code compilation issues with PIC / XC8 - expression generates no code 0

Hi, The following function: void acil_encode_cmd_setup(uint8_t *buffer, aci_cmd_params_setup_t *p_aci_cmd_params_setup, uint8_t setup_data_size) { *(buffer + OFFSET_ACI_CMD_T_LEN...
- pic xc8
4510 views

0 replies

Started over 8 years ago
by didier

Recent in Nordic blog

Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020