Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF51822 bluetooth smart beacon Antenna? 0

Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
- bluetooth low energy antenna
- nrf51822
892 views

0 replies

Started over 8 years ago
by TB
Not Answered
Unable to use eeprep tool 0

I am using a eeprep tool which can only be used with command prompt. I am struggling with it. Here is the format to use eeprep tool :- usage: eeprep [options] <infile...
- eeprom
1077 views

0 replies

Started over 8 years ago
by Anuj Mattoo
Not Answered

Impossible to debug or flash the examples with IAR & CMSIS-DAP 0

Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...

1272 views

0 replies

Started over 8 years ago
by agf
Not Answered
Ble Mesh and advertising 0

Hi, What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board When i download the app,why doesnt advertising exist.i cant...
- advertising
- mesh
983 views

0 replies

Started over 8 years ago
by Oguz Emre
Not Answered
Library for NRF905 on Raspberry Pi 0

Hi all, Is there any stable library for NRF905 on Raspberry Pi? Thanks and Regards, Wonderful IOT
- nrf905 raspberry pi library
2568 views

0 replies

Started over 8 years ago
by Wonderful IOT

Recent in Nordic blog

Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020