Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Why doesn't the PSM mode take effect after configuration? 0

Hello, I am currently developing a project using the nRF 9151 and SDK version v2.7.0. The issue I am facing is that I have configured the PSM mode, but it doesn't seem...
- development
- software
- nb-iot
- nRF9151
41 views

0 replies

Started 2 days ago
by GUOQI123
Not Answered
build failed when configuring the OOB legacy pairing only mode in NCS v2.8.0 0

Hello, I am using NCS v2.8.0. In this, when I configured the application to use OOB legacy pairing only mode, the build process failed. Following is the configuration...
24 views

0 replies

Started 2 days ago
by Narendra
Not Answered
Configure P0.05/P0.07 as GPIO when using uart0 0

I've got a custom board using an nRF52832. I'm using the P0.06/P0.08 as the TX/RX pins for UART comms, but don't need the P0.05/P0.07 pins for CTS/RTS. Is there anyway I can...
37 views

0 replies

Started 2 days ago
by Mike Austin (LPI)
Not Answered
nRF Connect for Desktop Bluetooth Low Energy stops working with nRF52840 devkit 0

Hello, I'm using my nRF52840 devkit together with nRF Connect for Desktop Bluetooth Low Energy (v4.0.4) app for some testing. The app failed to recognize my devkit. It used...
33 views

0 replies

Started 2 days ago
by John
Not Answered
Setting up custom Secure Bootloader 0

Hello Nordic Team, I'm developing an project using VS Code with nRF Connect Extension for an nRF52832 board. The SDK version I use is 2.7.0 , build system is sysbuild . I...
57 views

0 replies

Started 3 days ago
by wounderkid_

Recent in Nordic blog

Developing and testing Bluetooth Low Energy products on nRF52840 in Renode and Zephyr

Michael Gielda

The Bluetooth Low Energy (LE) connectivity standard has gained immense popularity in recent years, mainly due to the growing ubiquity of IoT solutions in both consumer electronics and industry. Thanks…
- 4 Jul 2022
Machine Learning with the Thingy:53

Øyvind

The Thingy:53 is our newest prototyping platform based on the nRF5340 SoC and it comes preprogrammed with firmware developed by Edge Impulse. This firmware supports all Edge Impulse features, including…
- 28 Jun 2022
LE Audio through a technical lens

Karl Ylvisaker

The highly anticipated nRF5340 Audio Development Kit and nRF Connect SDK software module is finally available. On that occasion, I am writing this blog post to quickly get everyone up to speed on the most…
- 20 May 2022

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019