Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF54L NRESET pin reference design termination 0

Hi, I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
31 views

0 replies

Started 1 day ago
by jlegstrong
Not Answered
SPI pins are outputting low voltages (100mV amplitude) 0

Hello, I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
- development
- spi
- hardware
- nRF5340
25 views

0 replies

Started 1 day ago
by LeeHagrid
Not Answered
What could the nRF52840 be doing while apparently idle — and what are the risks of interrupting it with a reset? 0

Hi, I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
61 views

0 replies

Started 1 day ago
by coiti4
Not Answered
nRF Cloud Connection using COAP Protocol (err:-111) 0

Hello, I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
40 views

0 replies

Started 1 day ago
by Aydogan
Not Answered
nRF52833 aQFN package 0

Hi, We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper. Do you have any footprint recommendations for 2oz copper...
27 views

0 replies

Started 1 day ago
by MBarBurtonems

Recent in Nordic blog

Nordic Semiconductor nRF51822 Firmware for Background Data Recording

scytulip

#Nordic Semiconductor nRF51822 Firmware for Background Data Recording Updating on https://github.com/scytulip/nrf51-back-rec Design Objective This firmware is designed for low-cost long-time low-power…
- 23 Oct 2014
Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014
How different BLE packet types influence throughput

Stefan Birnir Sverrisson

There are several types of write operations, write request with authorization, write request without authorization and write command. You can see message sequence charts for those messages here and he…
- 9 Oct 2014
Measuring Lithium battery voltage with nRF51

Stefan Birnir Sverrisson

Here is an example of a hardware setup to measure the voltage on a Lithium battery with a voltage divider and a connected capacitor. The Lithium battery typically has a voltage range of 2.7 - 4.2 V and…
- 2 Oct 2014