Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to get APP_ERROR_CHECK(err_code) to print out error msg instead of reset? 0

I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
- 130 sdk11 ble
- bluetooth low energy
1508 views

0 replies

Started over 8 years ago
by helpme
Not Answered
ble_app_uart does not support DFU(Device Firmware Update) 0

Hello All, I have problem with ble_app_uart which are not support DFU services. When I am implement both services device will not advertise. and when ble_nus uninitialized...
- nrf52
- ble_uart
- ble
- nrf51
- dfu
- ble_nus
1056 views

0 replies

Started over 8 years ago
by Rajneesh
Not Answered
Device not start after Bootloader/SoftDevice 0

[symptom] I want to update my application/bootloader/softdevice by DFU. Steps are shown below. bootloder/softdevice update if 1 step is done, application update...
- dfu
731 views

0 replies

Started over 8 years ago
by shtsht
Not Answered
Help needed to setup a 15 channel ANT network on the nRF52 development kit 0

Dear Developer Zone, I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
- nrf52 dk s332
1418 views

0 replies

Started over 8 years ago
by Colt
Not Answered
ESB Sources and how to change them 0

Hello, i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
- esb
1057 views

0 replies

Started over 8 years ago
by florian2840

Recent in Nordic blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015