Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to get APP_ERROR_CHECK(err_code) to print out error msg instead of reset? 0

I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
- 130 sdk11 ble
- bluetooth low energy
1442 views

0 replies

Started over 8 years ago
by helpme
Not Answered
ble_app_uart does not support DFU(Device Firmware Update) 0

Hello All, I have problem with ble_app_uart which are not support DFU services. When I am implement both services device will not advertise. and when ble_nus uninitialized...
- nrf52
- ble_uart
- ble
- nrf51
- dfu
- ble_nus
1005 views

0 replies

Started over 8 years ago
by Rajneesh
Not Answered
Device not start after Bootloader/SoftDevice 0

[symptom] I want to update my application/bootloader/softdevice by DFU. Steps are shown below. bootloder/softdevice update if 1 step is done, application update...
- dfu
673 views

0 replies

Started over 8 years ago
by shtsht
Not Answered
Help needed to setup a 15 channel ANT network on the nRF52 development kit 0

Dear Developer Zone, I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
- nrf52 dk s332
1355 views

0 replies

Started over 8 years ago
by Colt
Not Answered
ESB Sources and how to change them 0

Hello, i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
- esb
991 views

0 replies

Started over 8 years ago
by florian2840

Recent in Nordic blog

Current vs Voltage for nrf51 CPU

FormerMember

Since I couldn't find the information of how the supply current would change with different supply voltage for nrf51 chip, this is the result of a little test that I made to get this info. Setup: nrf51…
- 9 Sep 2015
Using Eclipse's Managed Make with the nRF51 DK

i_am_trying

I have been using Eclipse to programming+build+flash+debugging my nRF51 DK apps. This requires carrying a Makefile forward, modifying as stuff changes...handling flash programming in less integrated way…
- 6 Sep 2015
Programming Inexpensive nRf51822 modules with Nordic nRF51-DK

Mahesh Venkitachalam

I've updated my article on external SWD programming using the nRF51-DK. I have also designed an adapter board for these modules. http://electronut.in/nrf51-dk-external-programming/#E3BO
- 6 Sep 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019