Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Internal flash as a Non volatile storage for user data 0

Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash. External Flash memory has a lot of drawback in comparsion with internal...
- flash pstorage
1261 views

0 replies

Started over 8 years ago
by PanTikTak
Not Answered
List of available peripherals 0

Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]? I am using NRF5182...
- list
- peripheral
- nrf51822
- scan
827 views

0 replies

Started over 8 years ago
by Punit
Not Answered
How to get APP_ERROR_CHECK(err_code) to print out error msg instead of reset? 0

I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
- 130 sdk11 ble
- bluetooth low energy
1442 views

0 replies

Started over 8 years ago
by helpme
Not Answered
ble_app_uart does not support DFU(Device Firmware Update) 0

Hello All, I have problem with ble_app_uart which are not support DFU services. When I am implement both services device will not advertise. and when ble_nus uninitialized...
- nrf52
- ble_uart
- ble
- nrf51
- dfu
- ble_nus
1005 views

0 replies

Started over 8 years ago
by Rajneesh
Not Answered
Device not start after Bootloader/SoftDevice 0

[symptom] I want to update my application/bootloader/softdevice by DFU. Steps are shown below. bootloder/softdevice update if 1 step is done, application update...
- dfu
673 views

0 replies

Started over 8 years ago
by shtsht

Recent in Nordic blog

nRF52832-QFN Eagle Part/Footprint

ble_Man

Hello everyone, I've started an nRF52832 library for those devs who are interested in creating their PCB's in Eagle. Its the QFN chip right now. I read somewhere that a BGA version is planned also, so…
- 24 Jun 2015
Start Up Extreme Norway

John Leonard

Last week I attended what was my first Startup event, but after experiencing the energy there, I can safely say it will not be my last. 3 days of seminars, networking and lots of fun kicked off in Bergen…
- 22 Jun 2015
Step by Step Guide to Setup and Start Developing with the nRF51 DK and Keil

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, get the tools installed and get the software (SW) development environment…
- 17 Jun 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019