Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF5_SDK_11.0.0 Problems, why program not starts? 0

I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
- nrf52-qfaa-b0 nrf5_sdk_11.0.0
519 views

0 replies

Started over 9 years ago
by chamalow
Not Answered
PCA10031 Dongle failure under VirtualBox 0

Hi We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
1225 views

0 replies

Started over 9 years ago
by Ken N
Not Answered
Receiver sensitivity 0

We are using nRF51822 for our products. We want to know the min value of "Receiver sensitivity" when we use this chip for BLE. The Datasheet says "Receiver sensitivity...
- receiver sensitivity nrf51822
2263 views

0 replies

Started over 9 years ago
by makoto
Not Answered
How to send and recive data to mutiple peripheral devices 0

Dear The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral) shows how one central device can connect to multiple peripheral devices. ...
- multiple peripheral
675 views

0 replies

Started over 9 years ago
by sjkim
Not Answered
Eddystone URL parser is broken in MCP 0

In the MCP app, if I have the following service data for an Eddystone beacon: 0x10, // Eddystone-URL type 0x00, // TX power in dBm. This is a signed integer so 0xEE ...
824 views

0 replies

Started over 9 years ago
by Tim

Recent in Nordic blog

Multiple channels in RTT

Krzysztof Zaraska

Segger RTT (Real-Time Terminal) supports multiple data channels. RTT Viewer uses channel 0 only, and implements multiple virtual terminals on top of this. The terminal can be switched by SEGGER_RTT_SetTerminal…
- 29 Sep 2017
6 Things to Know about Bluetooth Beacons

Rose Martin

Smartphones and tablets have revolutionized the manner in which people communicate with each other. Mobile applications with location-based features like Bluetooth beacons, WiFi, and GPS are helping people…
- 22 Sep 2017
Creating a Keil project for a Bluetooth Mesh example (Updated for 0.10.0)

Kristian Skordal

Introduction The recently released nRF5 SDK for Bluetooth Mesh does not provide Keil project files for its example projects. Fortunately, it's relatively easy to set up your own project from scratch.…
- 19 Sep 2017
Using millis() like in Arduino.

schef

Here are two simple functions to use when you want to use timestamps for time measurement. uint32_t millis(void) { return(app_timer_cnt_get() / 32.768); } and for comperison of current with given…
- 18 Sep 2017
Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017