Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to send and recive data to mutiple peripheral devices 0

Dear The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral) shows how one central device can connect to multiple peripheral devices. ...
- multiple peripheral
652 views

0 replies

Started over 8 years ago
by sjkim
Not Answered
Eddystone URL parser is broken in MCP 0

In the MCP app, if I have the following service data for an Eddystone beacon: 0x10, // Eddystone-URL type 0x00, // TX power in dBm. This is a signed integer so 0xEE ...
795 views

0 replies

Started over 8 years ago
by Tim
Not Answered
Cannot connect to BLE devices requiring random LE address type with Android nRF app 0

I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect. I know Fitbit wristbandes...
2989 views

0 replies

Started over 8 years ago
by Axelle
Not Answered

Communication between Gazell and non-gazell devices 0

Hi, The situation: I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...

767 views

0 replies

Started over 8 years ago
by nordicdev
Not Answered
softdevicee s130 rssi problem 0

Hi everyone nrf51822,softdevice s130 2.0.0 now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
- nrf51822
- bluetooth low energy s130 rssi
576 views

0 replies

Started over 8 years ago
by xieyang

Recent in Nordic blog

SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014
How different BLE packet types influence throughput

Stefan Birnir Sverrisson

There are several types of write operations, write request with authorization, write request without authorization and write command. You can see message sequence charts for those messages here and he…
- 9 Oct 2014
Measuring Lithium battery voltage with nRF51

Stefan Birnir Sverrisson

Here is an example of a hardware setup to measure the voltage on a Lithium battery with a voltage divider and a connected capacitor. The Lithium battery typically has a voltage range of 2.7 - 4.2 V and…
- 2 Oct 2014

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019