Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

low power uart mode leaves TX asserted while CTS is disabled 0

I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...

643 views

0 replies

Started over 9 years ago
by Jim Dattolo
Not Answered
BLE nRF OpenMesh - data rates in typical configurations 0

Hello, I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture. I'm considering using it in a network consisting...
1412 views

0 replies

Started over 9 years ago
by piorossi
Not Answered
Is it useful to simulate my PCB design using CST Studio?and How? 0

Hello Nordic Community, I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
2036 views

0 replies

Started over 9 years ago
by mahmoud.tolba
Not Answered
registering to listen ble_ancs_c events 0

Hi. I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
- nrf52 s132 ble ancs sdk v11
820 views

0 replies

Started over 9 years ago
by Matts
Not Answered
PCB antenna used in the nRF51 DK 0

I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
- antenna nrf51dk
742 views

0 replies

Started over 9 years ago
by BCNLANYC

Recent in Nordic blog

Recover the nRF51 when nrjprog and nRFGo Studio couldn't

Hung Bui

You may have a nRF51 chip that is "bricked" and both nRFGo Studio and nrfjprog recover option doesn't work. You can try to use J-link Commander to recover. In some case, J-link Commander showed that it…
- 21 Jul 2014
nRF51 SDK v6.0.0 bug report and temporary workarounds

Hung Bui

I created this blog post to document the bugs reported on nRF51 SDK v6.0.0 The workaround for each bug would also be provided here as a temporary solution before the bug is fixed in the future release…
- 16 Jul 2014
S130 Multi-link SoftDevice released. Tell us what you think.

John Leonard

Our most advanced Bluetooth Smart SoftDevice to date is now - S130. We're excited in a big way about this one covering as it does so many different options in one protocol stack. Again, we always value…
- 10 Jul 2014

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019