Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How can I receive data from UART module 0

Hi all, I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
- 110 nrf51822 eclipse gcc uart
965 views

0 replies

Started over 8 years ago
by Mark
Not Answered

ble-sniffer_win_1.0.1_1111_Sniffer.exe exited unexpectedly 0

I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed. I am attaching the log.txt. log...

1789 views

0 replies

Started over 9 years ago
by Paul
Not Answered

From which function new node will get version detail for the first time in mesh 0

Hi all, I am using ble open mesh with pca10028 boards ble mesh is working fine. I am developing a application that has to blink led in mesh( without any delay between...

2206 views

0 replies

Started over 9 years ago
by Manjunath
Not Answered

low power uart mode leaves TX asserted while CTS is disabled 0

I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...

644 views

0 replies

Started over 9 years ago
by Jim Dattolo
Not Answered
BLE nRF OpenMesh - data rates in typical configurations 0

Hello, I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture. I'm considering using it in a network consisting...
1416 views

0 replies

Started over 9 years ago
by piorossi

Recent in Nordic blog

Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020