Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
asynchronous pulse counting in low power mode 0

Hello, I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode. Pulses are asynchronous The rate of pulses can...
1112 views

0 replies

Started over 9 years ago
by fakufaku
Not Answered
nRF52 SAADC gain error a function of Vcc? 0

Hi I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52. Both the reference resistor and the PT-100 is sampled while the voltage...
- nrf52
- adc
- gain
- vcc
- nrf52382
- saadc
2310 views

0 replies

Started over 9 years ago
by Visti Andresen
Not Answered
Sample multiple inputs with fixed rate using ADC hal 0

Hi I have been searching the forums, but were not able to find an answer to my question. I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
- adc
- oftdevice
1309 views

0 replies

Started over 9 years ago
by Phillip
Not Answered

NRF24L01 sends 0

Hi I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...

592 views

0 replies

Started over 9 years ago
by Mani
Not Answered

What values can the nRF905 status register have? 0

Hi I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...

688 views

0 replies

Started over 9 years ago
by Pieter Roos

Recent in Nordic blog

Start Up Extreme Norway

John Leonard

Last week I attended what was my first Startup event, but after experiencing the energy there, I can safely say it will not be my last. 3 days of seminars, networking and lots of fun kicked off in Bergen…
- 22 Jun 2015
Step by Step Guide to Setup and Start Developing with the nRF51 DK and Keil

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, get the tools installed and get the software (SW) development environment…
- 17 Jun 2015
Debugging using QtCreator on Mac

wim

This post started as a question, but got the suggestion to post this as a blog post. Here it is. I have been trying to get QtCreator configured such that I can use it as my IDE for the nrf51822 on Mac…
- 12 Jun 2015
Trying OpenWRT Chaos Calmer (15.05 RC1) on Raspberry Pi 2

Jun Qing ZOU

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D…
- 11 Jun 2015
Trying OpenWRT Chaos Calmer (15.05 RC1) on Asus RT-N16

Jun Qing ZOU

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D…
- 11 Jun 2015
Compatibility between DFU bootloader and DFU master

Hung Bui

We have been receiving quite a few questions about the compatibility issue between the bootloaders from different SDK versions and the DFU master such as nRF Master Control Panel, nRFToolbox, etc. In…
- 10 Jun 2015