Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11 0

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11. Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work. I think your library...

921 views

0 replies

Started over 10 years ago
by Chois
Not Answered

nRf24l01+ stand alone operation 0

In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...

1677 views

0 replies

Started over 10 years ago
by mikebuzz
Not Answered
IoT SDK How use ipv6_address_set / ipv6_address_remove API? 0

[Dev Env] nRF51 DK IoT SDK 0.8 IoT SoftDevice [Question] how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API. To...
741 views

0 replies

Started over 10 years ago
by cucu
Not Answered

nRF51822 USB dongle help 0

Hi Guys, I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine. We also have a MCU RTOS Emulator based on Qemu,we...

1493 views

0 replies

Started over 10 years ago
by tommyhung
Not Answered
[iOS: pairing cancelled] BLE GAP disconnection no more handle since SDK 7.3.0 ? 0

Hello, I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
- nrf51822 pairing io
927 views

0 replies

Started over 10 years ago
by Sebastien

Recent in the DevZone Blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018