Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
usb-to-uart firmware and driver 0

I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
- nrfg0 nrf24lu1p usb interface
859 views

0 replies

Started over 9 years ago
by Raj005
Not Answered
Can not create an SPI connection 0

I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
898 views

0 replies

Started over 9 years ago
by J50
Not Answered
IoT SDK - cannot connect to nrf51822 using newer linux kernel 0

Hello, Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3. Now, with the same configuration and hardware, I'm not...
- bluetooth 6lowpan
- 6lowpan
- debug
- linux
- nrf51822
- kernel
- iot
1228 views

0 replies

Started over 9 years ago
by Michal
Not Answered
IoT SDK - linux can't connect to NRf51 using new kernel 0

Hello, Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3. Now, with the same configuration and hardware, I'm not...
- router
- iot sdk
- 6lowpan
- nrf51
- 4.3
- linux
- bluetooth_6lowpan
- nrf51822
- kernel
- iot
1108 views

0 replies

Started over 9 years ago
by Michal
Not Answered

CE—compliant nRF24LU1+ module 0

Hi Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine. There are many modules...

523 views

0 replies

Started over 9 years ago
by Salvador Sancha

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015
nRF51 Qt GCC Example

Jacob Portukalian

Hi Everyone! At Sky Wave Design, we recently switched all of our Nordic development over to using GCC and using Qt Creator as the IDE. We have released our example project on github for those of you…
- 31 Jul 2015
ROM and RAM Management

Øyvind Karlsen

Introduction Here are some tips and tricks to manage your application size. RAM and ROM usage The total RAM usage is: ZI-data + RW-data The total flash usage is: Code + RO-data + RW-data …
- 28 Jul 2015