Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Writing data using Python binding method 0

Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...

797 views

0 replies

Started over 9 years ago
by Owlman
Not Answered

Can anyone explain ble event in Python? 0

Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...

646 views

0 replies

Started over 9 years ago
by Owlman
Not Answered

pstorage_store doesn't call callback 0

pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...

591 views

0 replies

Started over 9 years ago
by F
Not Answered

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11 0

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11. Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work. I think your library...

747 views

0 replies

Started over 9 years ago
by Chois
Not Answered

nRf24l01+ stand alone operation 0

In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...

1405 views

0 replies

Started over 9 years ago
by mikebuzz

Recent in Nordic blog

Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019