Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11 0

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11. Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work. I think your library...

747 views

0 replies

Started over 9 years ago
by Chois
Not Answered

nRf24l01+ stand alone operation 0

In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...

1408 views

0 replies

Started over 9 years ago
by mikebuzz
Not Answered
IoT SDK How use ipv6_address_set / ipv6_address_remove API? 0

[Dev Env] nRF51 DK IoT SDK 0.8 IoT SoftDevice [Question] how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API. To...
563 views

0 replies

Started over 9 years ago
by cucu
Not Answered

nRF51822 USB dongle help 0

Hi Guys, I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine. We also have a MCU RTOS Emulator based on Qemu,we...

1302 views

0 replies

Started over 9 years ago
by tommyhung
Not Answered
[iOS: pairing cancelled] BLE GAP disconnection no more handle since SDK 7.3.0 ? 0

Hello, I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
- nrf51822 pairing io
707 views

0 replies

Started over 9 years ago
by Sebastien

Recent in Nordic blog

Nordic Semiconductor nRF51822 Firmware for Background Data Recording

scytulip

#Nordic Semiconductor nRF51822 Firmware for Background Data Recording Updating on https://github.com/scytulip/nrf51-back-rec Design Objective This firmware is designed for low-cost long-time low-power…
- 23 Oct 2014
Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014
How different BLE packet types influence throughput

Stefan Birnir Sverrisson

There are several types of write operations, write request with authorization, write request without authorization and write command. You can see message sequence charts for those messages here and he…
- 9 Oct 2014
Measuring Lithium battery voltage with nRF51

Stefan Birnir Sverrisson

Here is an example of a hardware setup to measure the voltage on a Lithium battery with a voltage divider and a connected capacitor. The Lithium battery typically has a voltage range of 2.7 - 4.2 V and…
- 2 Oct 2014