Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF8001 Setup Error w/ EFM32 0

I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
- nrf8001 setup
1104 views

0 replies

Started over 9 years ago
by delo
Not Answered
Cannot connect or recover nrd51 dk 0

Hi, I have 3 nRF51 DK pca10028 v1.1.0 I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
- nrfgo studio recover jlink
1166 views

0 replies

Started over 9 years ago
by eozkucur
Not Answered

Power Issue with nRF51822 0

Hi Guys, Thanks for your precious time and insight. Let me try to explain what we did, We have developed a custom board After assembling the board, we do a bare board...

592 views

0 replies

Started over 9 years ago
by deepu
Not Answered
ADXL 345 Tutorial 0

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
- ADXL 345
- spi
- adxl
2953 views

0 replies

Started over 9 years ago
by Milad
Not Answered

Revised spi_master to utilize a mask for cs 0

Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...

1068 views

0 replies

Started over 9 years ago
by nszmnsky

Recent in Nordic blog

Programming the nRF51822 Beacon Kit with the nRF51DK

Stefan Birnir Sverrisson

One way to program the nRF51822 Bluetooth Smart Beacon Kit is to use the nRF51 DK. This gives you a full scale development platform (the nRF51 DK). This blog will go thru the steps needed to program…
- 7 May 2015
Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015
Building kernel for RPi2 with bluetooth_6lowpan for Raspbian

Håkon Alseth

Building kernel for RPi2 with bluetooth_6lowpan In this guide, you will have two choices: Cross-compilation build Native build Choose the one that fits your needs. Cross-compilation is…
- 9 Apr 2015
Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015