Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
If the nRESET is held low of nRF52840, would it shut it down? 0

Hi, What would be the state of SWD/SWCLK be when the nRF52840 is held in RESET mode? I am thinking if a simple gang programming be implemented by SWD/SWCLK be shared among...
19 views

0 replies

Started 8 hours ago
by kaushalyasat
Not Answered
Timing of retransmissions 0

Hi there, We are currently developing a system, where around 480 kbytes of data are transmitted over BLE. Throughput is supposed to be as high as possible. We are using...
15 views

0 replies

Started 10 hours ago
by JonasD27
Not Answered
VoIP support for nRF91x LTE Modules 0

Hello, Is there any documentation on setting up VoIP on the nRF91x module with Zephyr? As the nRF91x does not have a built-in VoIP app layer, I can assemble the hardware...
- nRF9160
- nRF Connect SDK
- Evaluation
- nRF9151
- zephyr
- hardware
15 views

0 replies

Started 11 hours ago
by 4HERE_Corp
Not Answered
Regulator fixed is broken in nrf sdk 3.2.1 0

After upgrading nRF Connect SDK from 3.1.1 to 3.2.1, our fixed regulator stopped working. We are on nRF54L15. Tracking it down further, this seems to be some sort of GPIO...
26 views

0 replies

Started 12 hours ago
by Konstantin Klitenik
Not Answered
Nordic Academy Cellular IoT Fundamentals Lesson 4 Exercise 2 (l4_e2): MQTT Connect error -111 even in the solution build 0

We are running some internal training on cellular, and it seems that Lesson 4, Exercise 2 is missing something (in the tab for NCS v3.2.0); the instructions to provide the...
8 views

0 replies

Started 12 hours ago
by Matteo Elimo

Recent in the DevZone Blog

Multiple channels in RTT

Krzysztof Zaraska

Segger RTT (Real-Time Terminal) supports multiple data channels. RTT Viewer uses channel 0 only, and implements multiple virtual terminals on top of this. The terminal can be switched by SEGGER_RTT_SetTerminal…
- 29 Sep 2017
6 Things to Know about Bluetooth Beacons

Rose Martin

Smartphones and tablets have revolutionized the manner in which people communicate with each other. Mobile applications with location-based features like Bluetooth beacons, WiFi, and GPS are helping people…
- 22 Sep 2017
Creating a Keil project for a Bluetooth Mesh example (Updated for 0.10.0)

Kristian Skordal

Introduction The recently released nRF5 SDK for Bluetooth Mesh does not provide Keil project files for its example projects. Fortunately, it's relatively easy to set up your own project from scratch.…
- 19 Sep 2017
Using millis() like in Arduino.

schef

Here are two simple functions to use when you want to use timestamps for time measurement. uint32_t millis(void) { return(app_timer_cnt_get() / 32.768); } and for comperison of current with given…
- 18 Sep 2017
Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017