Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Coexistence of legacy and NRFX configuration in sdk_config.h 0

I noticed that through apply_old_config.h configuration values like NRFX_CLOCK_ENABLED in sdk_config.h simply get overriden by the old CLOCK_ENABLED, so that there is no point...
12 views

0 replies

Started 1 hour ago
by Daniel Dakhno
Not Answered
Unable to Program Custom nRF52840 Board Using SWD with nRF52840 DK v2.0.1 0

I have designed and built a custom nRF52840 board and I’m experiencing difficulties programming it via SWD using an nRF52840 DK (version 2.0.1). When I connect my custom board...
10 views

0 replies

Started 1 hour ago
by sdfksdfhfs
Not Answered
ADV data parse, system assert Invalid spinlock 0

Hi I have a beacon sending out some data, and I have already finish the TX side, I also want to have a RX side to receive the data, in addition, as there are many other...
13 views

0 replies

Started 3 hours ago
by Ziyao Zhou
Not Answered
Where is it documented which services are required by other services/peripherals? 0

Hello, I am setting up a board configuration for my custom board and trying to get a bluetooth sample (heart rate profile) to compile using the board configuration. ...
12 views

0 replies

Started 4 hours ago
by JustEnoughDucks
Not Answered
mesh sensor observer sample on nrf52840 USB dongle 0

Hello, I am developing a mesh solution when the nrf52840 USB dongle will act as an observer. I am using the mesh sensor observer sample. I am able to build and flash...
12 views

0 replies

Started 5 hours ago
by bjornolsen

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020