Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
The need of having own company identification for mass production of BLE device 0

Hi everyone, We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
7 views

0 replies

Started 7 minutes ago
by Tai
Not Answered
What is the correct way to add an extra conf file for MCU boot with sysbuild? 0

Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
10 views

0 replies

Started 27 minutes ago
by dave
Not Answered
Adafruit e-link 2.13 Featherwing colour dispaly not working with nRF54L15DK 0

Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
- development
- software
- nRF54L15
- spi
- zephyr
11 views

0 replies

Started 42 minutes ago
by pradeep2481
Not Answered
looking for basic start up for NRF24L01 0

Hi, i am looking for basic start up parameters for a 24L01. I do all my programm in assembler (sorry i am old). what i aim to do is simple TX-RX, like a small remote...
11 views

0 replies

Started 49 minutes ago
by patallen
Not Answered
Creating JITP Certificates in NRFCloud 0

We are using this manual screen to generate JITP certificates, but we need to automate for speed. I am trying to automate with this url but I get a 404 error https:/...
12 views

0 replies

Started 1 hour ago
by crotberg

Recent in Nordic blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015