Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
GRTC resets after sys_poweroff when using MCUboot (ncs 3.1.0) 0

Hello Nordic team, We are using the GRTC on the nRF54L15 , and we are observing the following behavior: When MCUboot is enabled , the GRTC (likely backed by SYSCOUNTER...
20 views

0 replies

Started 2 hours ago
by ddiassword
Not Answered
AT Command Documentation for NTN Development on nRF9151-LACA-A1A-R (SLM Mode) 0

Hi everyone, I’m currently working with the nRF9151-LACA-A1A-R module, developing NTN communication features using SLM mode. However, I haven’t been able to find any documentation...
16 views

0 replies

Started 3 hours ago
by felipe.eaware
Not Answered
HTTP Client + W5500 on nRF5340: Works with IP but fails with domain names (DNS resolution fails) 0

Hi everyone, I’m trying to use the HTTP client sample from NCS v3.0.2 with a W5500 Ethernet shield on an nRF5340. DHCP works fine, and I can successfully POST and GET using...
8 views

0 replies

Started 7 hours ago
by Haris Iqbal
Not Answered
PPK II reliability and interaction with DC/DC converters 0

Hi, We've been using the PPK II for basically every IoT project we've carried out in the last few years, and it has been an incredibly useful tool. Our standard use case...
13 views

0 replies

Started 7 hours ago
by ecasado_iz
Not Answered
GPS CN0 Test 0

If you have tested the nRF9151's GPS with the CMW100 or IQ station. We need to know: 1. What test waveform file is required? 2. Should we use the ARB file or the CW waveform...
8 views

0 replies

Started 8 hours ago
by Bruce Chen

Recent in the DevZone Blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015