Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF52840 DK dual UARTs: Debug on UART1, sensor on UART0 0

Hi, I’m working with an nRF52840 DK and trying to use two UARTs simultaneously. I’ve configured UART1 for debugging (console and shell output) and want to use the default...
20 views

0 replies

Started 48 minutes ago
by lexiegss
Not Answered
How to configure software code for external PA chip in NCS-SDK? 0

Hi, Based on the example of dect_shell in NCS, how can I modify the software code to make the external PA chip work properly?
18 views

0 replies

Started 1 hour ago
by jszhang
Not Answered
How to debug MCUboot swap failure after OTA DFU? boot_request_upgrade() has no effect 0

Hi everyone, I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
20 views

0 replies

Started 3 hours ago
by QBSho
Not Answered
Code build errors with DFU(mcuboot) and File systems on Custom board nRF52840 0

I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
15 views

0 replies

Started 3 hours ago
by Macherla Swetha
Not Answered
Bypass on-board CODEC of nRF5340 Audio DK for multiple microphones interface 0

Hello, We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
31 views

0 replies

Started 4 hours ago
by Aditya P

Recent in Nordic blog

Step by Step Guide to Setup and Start Developing with the nRF51 DK and Keil

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, get the tools installed and get the software (SW) development environment…
- 17 Jun 2015
Debugging using QtCreator on Mac

wim

This post started as a question, but got the suggestion to post this as a blog post. Here it is. I have been trying to get QtCreator configured such that I can use it as my IDE for the nrf51822 on Mac…
- 12 Jun 2015
Trying OpenWRT Chaos Calmer (15.05 RC1) on Raspberry Pi 2

Jun Qing ZOU

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D…
- 11 Jun 2015
Trying OpenWRT Chaos Calmer (15.05 RC1) on Asus RT-N16

Jun Qing ZOU

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D…
- 11 Jun 2015
Compatibility between DFU bootloader and DFU master

Hung Bui

We have been receiving quite a few questions about the compatibility issue between the bootloaders from different SDK versions and the DFU master such as nRF Master Control Panel, nRFToolbox, etc. In…
- 10 Jun 2015
"OpenWRT Series" #1: setting up TP-Link WDR4300 (or N750) for Bluetooth Low Energy 6LoWPAN

PK

The first version of Nordic IoT SDK has been released over 6 months. Till now, there have been no well-known router solutions supporting Bluetooth Low Energy over IPv6. This made us the BLE application…
- 10 Jun 2015