Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to integrate the Edge Impulse SDK into an ncs3.3.0 project to run EI models 0

I have installed ncs3.3.0 and want to keep ncs unaffected. According to the document docs.nordicsemi.com/.../sdk_setup.html , I should choose to import the edge impulse SDK...
9 views

0 replies

Started 20 minutes ago
by llly
Not Answered
Does nRF54L15 support BLE stable modulation characteristics at 1Mb/s & 2 Mb/s..., if we meet related issue, how to debug on HW and SW side? 0

Dear Nordic Team and Distributors, For nRF54L15 (CSP and QFN) design circuits, how to optimize the stable modulation issue? What aspects should we consider to do failure...
12 views

0 replies

Started 50 minutes ago
by gengyuanfa
Not Answered
P822601 Internal PCB Antenna Poor Performance vs External Antenna on nRF9151 0

Hi, nRF9151 + Kyocera AVX P822601 internal SMT antenna: 8 dB RSRP loss vs external antenna — possible PCB layout issue? Test Results Test 1 — Out of Faraday cage, internal...
14 views

0 replies

Started 58 minutes ago
by Piyush Devani
Not Answered
nPM2100 VBAT reads NACK while nRF7002 WiFi is active 0

System Context Host MCU: nRF54H20 (Custom Board) PMIC: nPM2100 (Connected via TWI/I2C) RF Co-processor: nRF7002 Wi-Fi (Powered by nPM2100 VOUT ) Software...
14 views

0 replies

Started 1 hour ago
by kile.gc
Not Answered
nRF5340 with DS3231 as LXFO 0

Hi, I would like to seek a guidance with proper usage of DS3231 as LFXO with nRF5340. HW: Custom board, DS3231 32kHz output connected to nRF's X1 with pull-up resistor...
16 views

0 replies

Started 1 hour ago
by reavertm

Recent in the DevZone Blog

Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015
How to use the latest Keil 5 for Keil 4 projects (.uvproj)

Stefan Birnir Sverrisson

As many have noticed, Keil 5 does not have native support for Keil 4 projects (project files ending with uvproj), it only has native support for Keil 5 projects (project files ending with uvprojx). However…
- 26 Mar 2015
The Google UriBeacon Project

Jason

Overview The UriBeacon design allows a Bluetooth Low Energy (BLE) device to periodically transmit an ADV packet that contains a URI. This technology enables any device, place or thing to become a beacon…
- 17 Mar 2015
Flashing SoftDevice directly from ARM Keil uVision and Makefile (nRF51 SDK 8.0.0)

Krzysztof Chruscinski

Since nRF51 SDK version 8.0.0 SoftDevices binary files have become a part of the release. In order to make it easier to flash proper type and version of SoftDevice a new feature was added: each project…
- 16 Mar 2015
6LoWPAN for Bluetooth low energy on OpenWRT

Glenn Ruben Bakke

OpenWRT is one of the most popular open source Linux-based router firmware alternatives for commodity routers. From kernel 3.17, Linux has supported 6LoWPAN for Bluetooth low energy (BLE) through the…
- 13 Mar 2015