Error when trying to use the PDM interface

[Espen]

Hi

I am trying to collect data from a PDM microphone with the nRF5340DK and using the nRF Connect SDK. I am loosely following the example posted here, but without the SD-card part.

The code in my main file looks like this:

#include <zephyr/kernel.h>

#include <zephyr/drivers/i2c.h>

#include <zephyr/logging/log.h>

#include <nrfx_pdm.h>

#define _pin_clk 18

#define _pin_din 16

static const int size = 4096;

bool flag = 0;

bool WriteFlag = 0;

int16_t buff1[4096];

int16_t buff2[4096];

LOG_MODULE_REGISTER(Main);

static void drv_pdm_hand(const nrfx_pdm_evt_t *evt){

    if((*evt).buffer_requested){

        nrfx_err_t error;

        if(!flag){

            error = nrfx_pdm_buffer_set(&buff1[0], size);

            flag = 1;

            WriteFlag = 1;

        }

        else{

            error = nrfx_pdm_buffer_set(&buff2[0], size);

            flag = 0;

            WriteFlag = 1;

        }

    }

}

int main(void)

{

    nrfx_err_t error;

    nrfx_pdm_config_t config1 = NRFX_PDM_DEFAULT_CONFIG(_pin_clk, _pin_din);

    error = nrfx_pdm_init(&config1, &drv_pdm_hand);

   

   

    error = nrfx_pdm_start();

    k_msleep(1000);

    error = nrfx_pdm_stop();

    LOG_INF("DONE");

    return 0;

}

And my config file looks like this:

CONFIG_LOG=y

CONFIG_NRFX_PDM=y

When I run it like this, I get the error:
[00:00:00.252,227] <err> os: >>> ZEPHYR FATAL ERROR 1: Unhandled interrupt on CPU 0
[00:00:00.252,288] <err> os: Current thread: 0x20008738 (main)
[00:00:00.277,313] <err> fatal_error: Resetting system

I then included:

bool clear = nrfx_pdm_enable_check();

    if(clear){

        LOG_INF("The PDM interface is enabled");

    }

    else{

        LOG_INF("The PDM interface is disabled");

    }

From here I always get that the PDM interface is disabled. So I suspect that this is the problem. How do i go about enabling the PDM interface?

[Naeem Maroof]

Hi Espen,

Thank you for contacting DevZone at NordicSemi.

As you are using NRFX driver, you typically have to connect the Interrupt Request (IRQ).

Modifying the code as following should resolve the issue:

int main(void)
{
    //...
    
    IRQ_DIRECT_CONNECT(PDM0_IRQn, 0, nrfx_pdm_irq_handler, 0);
	error = nrfx_pdm_init(&config1, &drv_pdm_hand);
	printk("\nThe Value Returned by PDM_INIT() = %d \n", (int) error);
	if(error != NRFX_SUCCESS )
	{
		//do what ever kind of error handling you want
		return 0;
	}
	//in case of success, call pdm_start()	
	
	//...
	
}

Regards,
Naeem

[Espen]

Thank you so much. That resolved the error. For a follow up question, what does the IRQ_DRIECT_CONNECT macro do?

[Espen]

When I test it, for some reason, I cant detect the clock signal or data signal using a logic analyzer.

I am unsure what the problem might be. Have I skipped a step when making the clock signal?

[Naeem Maroof]

Do you have any overlay file?

How does your compiled DTS look?

and how is your hardware setup.

[Espen]

I do not have an overlay file. Is that required for this case? I got the pin numbers from the file "C:\ncs\v2.4.0\zephyr\boards\arm\nrf5340dk_nrf5340\nrf5340_cpuapp_common.dts", I thought that might be all that was necessary. I use pin p1.14 for _pin_clk and p1.12 for _pin_din. That should correspond to 18 and 16 respectively.

Further, what do you mean by "compiled DTS", where do I find that?

When using the logic analyzer, I have both measured with the mic connected and directly at the board pin(p1.14), but no clock signal is detected either way. So the problem seems to be on the board.