How to connect external 3.3V I/F I2S signal to nrf5340-audio-dk

[MontBlanc]

Hello,
devzone.nordicsemi.com/.../set-nrf5340-audio-dk-as-i2s-slave-over-external-bus
Based on this post, I changed I2S to SLAVE setting.
The external I2S I/F level is 3.3V.
When OB/EXT is green, it is noisy when I2S of 3.3V I/F is connected to P5, but we have confirmed that the audio signal is sent to the RX side and the sound is heard.

devzone.nordicsemi.com/.../access-to-i2s-interface-on-nrf5340-audio-dk

Based on this post, I tried changing the I2S port.
If OB/EXT lights up orange, does that mean the port has been changed to P10 instead of P5?

But when OB/EXT is orange, there is no sound even if you forcefully connect the 3.3V I/F to P10.

Also, in order to change the 3.3V I/F to 1.8V I/F, I changed the I2S signal level using TI's TXS0108E.
When I connect the nrF5340 to the enabled I2S port (P5 or P10), I checked with an oscilloscope and found that there is quite a lot of noise on the I2S signal.
Since it is a bidirectional buffer, it seems that the noise component is flowing backwards, or the GND level is not stable and crosstalk noise is being buffered.

Is there a way to run nrF5340-audio-DK with 3.3V I/F?
Or is there a good way to make I2S a 1.8V I/F?

[MontBlanc]

Hello,

When connected to P5, I found that the output of CIRRUS's CODEC collided with the external 3.3V I/F, causing the audio to be heard mixed with noise.
With the P5 connection, even if the level shift is correct, noise (output from CIRRUS) will be mixed in the I2S DATA line and no sound will be produced.

Also, I have connected the P10 to the 1.8V I/F I2S with a software setting that turns OB/EXT orange, but there is no sound.
Could you please give me detailed steps to use external hardware codec?

[Karl Ylvisaker]

Hello,

Just to aid my understanding so that I may best advice you, is your overall goal to interface the nRF5340 Audio DK with an external hardware codec that outputs I2S at 3.3V?

MontBlanc said:

Could you please give me detailed steps to use external hardware codec?

Please follow these steps to work with an external hardware codec:

Best regards,
Karl

[Karl Ylvisaker]

Hello,

Thank you for your extreme patience with this.

MontBlanc said:

Modifying the source code to use external I2S in v2.4.2 worked fine.
I modified the source code to use external I2S in v2.2.0 using the same procedure, but noise is always output to I2S DATA. (At this time, I have not yet modified the source code to make it stereo.)

I want to send and receive external I2S in stereo with v2.4.2.

I understand this to mean that it is working to sending and receiving external I2S stereo audio in v2.4.2, is this correct?
If not, could you elaborate and clarify on the issues you are currently facing with this approach using v2.4.2?

Is there any reason why you would like to use the nRF Connect SDK v2.2.0 instead of v2.4.2? Many new features and improvements have been added in between these releases, and now the v2.5.0 is also out - I would recommend upgrading to, and using, the latest nRF Connect SDK version whenever possible.

Best regards,
Karl

[MontBlanc]

Hello,
The latest version when I started working on it was v2.4.2. Since the current latest version is v2.5.0, I will make the same modifications here and try external I2S connection. Please check the modifications to the stereo conversion source code in v2.5.0.

Best Regards.

[Karl Ylvisaker]

Hello again,

Thank you for your patience with this.
Please have a look at this sample based on v2.4.0 as a reference to see the necessary changes to make it a stereo demo.

Best regards,
Karl

[MontBlanc]

Hello, Karl.

Thank you for answering.

Confirmed that the sound is played correctly in external I2S SLAVE mode with v2.4.0,
After that, I implemented all the changes you suggested.

The result is an interrupted mechanical sound that is linked to the played sound.
When there is no sound, there is no sound.
It seems that I2S transmission and reception are not being performed correctly.

If only prj.conf is restored to the original external I2S settings, the audio will be played in monaural with the correct sound.

Therefore, we assume that there is a problem somewhere in the processing branched at HEADSET.
Don't you know what the reason is?

Best Regards.

[Karl Ylvisaker]

Hello,

MontBlanc said:

Thank you for answering.

No problem at all, I am happy to help! :)

MontBlanc said:

Confirmed that the sound is played correctly in external I2S SLAVE mode with v2.4.0,
After that, I implemented all the changes you suggested.

Does this mean that you verified the audio going into the nRF5340 (i.e verified that your external codec provided the correct audio to the nRF), or does it mean that you were able to hear the stereo audio correctly through the LE Audio link when you used the referenced branch as provided, prior to any changes?

MontBlanc said:

The result is an interrupted mechanical sound that is linked to the played sound.

If there are glitches on top of the received audio then there is a chance that something has gone wrong in the handling of the received audio frames.
Could you elaborate further on the question above, so that I better can understand the issue you're seeing?

Best regards,
Karl

[MontBlanc]

Hello,
The environment I tried is as follows.

Environment of external CODEC without using nrf5340
External HOST(I2S SLAVE) - I2S(L/R) - External DAC(I2S MASTER) - L/R ch audio is output from L/R ch

Customized nrf5340 software for external CODEC
External HOST(I2S SLAVE) - I2S(L/R) - nrf5340-audio-dk TX - nrf5340-audio-dk RX(Left) - I2S(Lch) - External DAC(I2S MASTER) - Lch audio is output from Lch
|
- nrf5340-audio-dk RX(Right) - I2S(Rch audio is Lch packet) - External DAC(I2S MASTER) - Rch audio is output from Lch

Environment where I tried to send/receive L/Rch this time
External HOST(I2S SLAVE) - I2S(L/R) - nrf5340-audio-dk TX - nrf5340-audio-dk RX - I2S(L/R ch packet is incorrect) - External DAC(I2S MASTER) - L/R ch audio is output from L/R ch, However, the sound is mechanical

Best Regards.

[Karl Ylvisaker]

Hello,

Thank you for your extreme patience with this, and for the clarifications.

MontBlanc said:

nrf5340-audio-dk RX(Right) - I2S(Rch audio is Lch packet) - External DAC(I2S MASTER) - Rch audio is output from Lch

Is the only issue here that the R channel audio is output from the L channel? Is the audio quality as expected, and equal to the audio output on the nRF5340-audio-dk RX(left) that is acting as the I2S master?

MontBlanc said:

I2S(L/R ch packet is incorrect) - External DAC(I2S MASTER) - L/R ch audio is output from L/R ch, However, the sound is mechanical

Are you here configuring the headset device to be an I2S slave to the External DAC as the I2S master? In this case, I would assume that the output could be distorted since the nRF5340 is not in control of the I2S interface, and so it can not adjust the frequency of the MCLK to compensate for the drift in the reception timestamp.
Could you share some of your implementation here, so that I can take a look at how you are handling the packet reception and output?

Best regards,
Karl

[MontBlanc]

I made the changes below.

main.c
#include <hal/nrf_gpio.h>

and added
nrf_gpio_cfg_output(21);
nrf_gpio_pin_set(21);
inside
int main(void){}

audio_system.c
"ret = hw_codec_init();"
delete

hw_codec.c
Change all "return ret" in to "retuern 0"

Are there any other changes?

audio_i2s.c

.mode = NRF_I2S_MODE_SLAVE, // MODIFIED
.format = NRF_I2S_FORMAT_ALIGNED, // MODIFIED
.alignment = NRF_I2S_ALIGN_LEFT,
.ratio = NRF_I2S_RATIO_256X, // MODIFIED
.mck_setup = NRF_I2S_MCK_DISABLED, //0x66666000, MODIFIED

[MontBlanc]

Hello,

CONFIG_TRANSPORT_BIS=y was set extra.
When this setting was removed, L/R monaural transmission was possible.
The results are below.

.format = NRF_I2S_FORMAT_I2S
.alignment = NRF_I2S_ALIGN_LEFT

.sample_wodth = NRF_I2S_SWIDTH_16BIT
Lch Silent, Rch OK, No noise

.sample_wodth = NRF_I2S_SWIDTH_16BIT_IN32BIT
Lch Silent, Rch OK, No noise

.sample_wodth = NRF_I2S_SWIDTH_24BIT
Lch OK, Rch Silent, small noise mixed

.sample_wodth = NRF_I2S_SWIDTH_24BIT_IN32BIT
Lch OK, Rch Silent, small noise mixed

.sample_wodth = NRF_I2S_SWIDTH_32BIT
Lch OK, Rch Silent, No noise

I'd like to send and receive in stereo, but it's not working.
What should I fix?

Best Regards.

[MontBlanc]

In addition, the specifications of I2S are
LRCK=48kHz
BCLK=64Fs
16bit I2S (Left alignment)
is input to nrf5340 on the sending side.