nRF connect SDK ,Matter OTA

[DoubleAmaing]

Hi,

We are debugging the OTA function of Matter and using nrf52840 IC, but our board is relatively small, so we cannot use the Flash IC of the example; We are using IS25LP080D;

We have modified the relevant configuration of QSPI and the program can run correctly, but we encountered a problem during OTA,

The UART printing information is as follows:

May I ask what error this may be? Thank you for your help

I: 448320 [EM]>>> [E:33130i S:45885 M:240345016 (Ack:209591795)] (S) Msg RX from 1:0000000000000001 [CFC8] --- Type 0001:09 (IM:InvokeCommandResponse)
I: 448333 [DMG]Received Command Response Data, Endpoint=0 Cluster=0x0000_0029 Command=0x0000_0001
D: 448342 [SWU]QueryImageResponse:
D: 448345 [SWU]  status: 0
D: 448348 [SWU]  imageURI: bdx://0000000000000001/../xlc-matter/build_1/zephyr/matter.ota
D: 448356 [SWU]  softwareVersion: 12
D: 448359 [SWU]  softwareVersionString: R1.2
D: 448363 [SWU]  updateToken: 32
D: 448366 [SWU]  userConsentNeeded: 0
D: 448369 [SWU]Update available from version 11 to 12
I: 448375 [EM]<<< [E:33130i S:45885 M:209591796 (Ack:240345016)] (S) Msg TX to 1:0000000000000001 [CFC8] --- Type 0000:10 (SecureChannel:StandaloneAck)
I: 448388 [IN](S) Sending msg 209591796 on secure session with LSID: 45885
D: 448397 [SWU]Establishing session to provider node ID 0x0000000000000001 on fabric index 1
I: 448406 [DIS]Found an existing secure session to [1:0000000000000001]!
D: 448412 [DIS]OperationalSessionSetup[1:0000000000000001]: State change 1 --> 5
D: 448419 [SWU]BDX::SendMessage
I: 448423 [EM]<<< [E:33131i S:45885 M:209591797] (S) Msg TX to 1:0000000000000001 [CFC8] --- Type 0002:04 (BDX:ReceiveInit)
I: 448434 [IN](S) Sending msg 209591797 on secure session with LSID: 45885
I: 448542 [EM]>>> [E:33131i S:45885 M:240345017 (Ack:209591797)] (S) Msg RX from 1:0000000000000001 [CFC8] --- Type 0002:05 (BDX:ReceiveAccept)
D: 448555 [SWU]BDX::SendMessage
I: 448558 [EM]<<< [E:33131i S:45885 M:209591798 (Ack:240345017)] (S) Msg TX to 1:0000000000000001 [CFC8] --- Type 0002:10 (BDX:BlockQuery)
I: 448571 [IN](S) Sending msg 209591798 on secure session with LSID: 45885
I: 448924 [EM]>>> [E:33131i S:45885 M:240345018 (Ack:209591798)] (S) Msg RX from 1:0000000000000001 [CFC8] --- Type 0002:11 (BDX:Block)
E: Failed to get device for area '"mcuboot_secondary"'
E: ***** BUS FAULT *****
E:   Instruction bus error
E: r0/a1:  0x00000000  r1/a2:  0x200315b8  r2/a3:  0x200315bc
E: r3/a4:  0x843901b1 r12/ip:  0x000d1838 r14/lr:  0x000a2223
E:  xpsr:  0x410f0000
E: s[ 0]:  0x00000000  s[ 1]:  0x00000000  s[ 2]:  0x00000000  s[ 3]:  0x00000000
E: s[ 4]:  0x00000000  s[ 5]:  0x00000000  s[ 6]:  0x00000000  s[ 7]:  0x00000000
E: s[ 8]:  0x00000000  s[ 9]:  0x00000000  s[10]:  0x00000000  s[11]:  0x00000000
E: s[12]:  0x00000000  s[13]:  0x00000000  s[14]:  0x00000000  s[15]:  0x00000000
E: fpscr:  0x00000000
E: Faulting instruction address (r15/pc): 0x843901b0
E: >>> ZEPHYR FATAL ERROR 27: Unknown error on CPU 0
E: Current thread: 0x200145b0 (CHIP)
E: Halting system

[Simonr]

Hi

I've been assigned to this case now to check your QSPI config. Do you have a link to the IS25LP80D flash IC datasheet so I can give it a read to make sure all of this looks correct. The error messages you're seeing (-5) usually points to a I/O error, so what pins are you using for connecting the flash to your nRF52840?

Best regards,

Simon

[DoubleAmaing]

Hi,

Thank you.

I have read the manuals for MX25R64 and IS25LP080D, so I know their pins are compatible; So, I didn't replace the customer board, I just replaced the Flash IC; When using MX25R64, the OTA function runs successfully;

I will upload the manual for IS25LP080D, thank you.

I will upload my QSPI configuration and pin configuration;

I changed the writeoc to another one for testing, but the results were all unsuccessful;

.

&qspi {
	status = "okay";
	pinctrl-0 = <&qspi_default>;
	pinctrl-1 = <&qspi_sleep>;
	pinctrl-names = "default", "sleep";
	is25lp: is25lp80d@0 {
		compatible = "nordic,qspi-nor";
		reg = <0>;
		/* MX25R64 supports only pp and pp4io */
		writeoc = "pp";//"pp4io";
		/* MX25R64 supports all readoc options */
		readoc = "fastread";//"read4io";
		sck-frequency = <8000000>;
		jedec-id = [9D 60 14];//c2 28 17
		sfdp-bfp = [
		e5 20 f9 ff  ff ff 7f 00  44 eb 08 6b  08 3b 80 bb
		fe ff ff ff  ff ff 00 ff  ff ff 44 eb  0c 20 0f 52
		10 d8 00 ff  43 32 a5 00  82 d8 01 a7  ec 8d 69 4c
		7a 75 7a 75  f7 a2 d5 5c  4a c2 2c ff  e1 30 60 80 
	  /*e5 20 f1 ff  ff ff ff 03  44 eb 08 6b  08 3b 04 bb
		ee ff ff ff  ff ff 00 ff  ff ff 00 ff  0c 20 0f 52
		10 d8 00 ff  23 72 f5 00  82 ed 04 cc  44 83 68 44
		30 b0 30 b0  f7 c4 d5 5c  00 be 29 ff  f0 d0 ff ff*/
		];
		size = <8388608>;//// 8 Mbits. 1Mbit = 1048576
		has-dpd;
		t-enter-dpd = <10000>;
		t-exit-dpd = <35000>;
	};
};

-----------------------------------------------
pin config

qspi_default: qspi_default {
		group1 {
			psels = <NRF_PSEL(QSPI_SCK, 0, 17)>,
				<NRF_PSEL(QSPI_IO0, 0, 20)>,
				<NRF_PSEL(QSPI_IO1, 0, 13)>,
				<NRF_PSEL(QSPI_IO2, 0, 22)>,
				<NRF_PSEL(QSPI_IO3, 0, 24)>,
				<NRF_PSEL(QSPI_CSN, 0, 15)>;
			nordic,drive-mode = <NRF_DRIVE_H0H1>;
		};
	};

	qspi_sleep: qspi_sleep {
		group1 {
			psels = <NRF_PSEL(QSPI_SCK, 0, 17)>,
				<NRF_PSEL(QSPI_IO0, 0, 20)>,
				<NRF_PSEL(QSPI_IO1, 0, 13)>,
				<NRF_PSEL(QSPI_IO2, 0, 22)>,
				<NRF_PSEL(QSPI_IO3, 0, 24)>;
			low-power-enable;
		};
		group2 {
			psels = <NRF_PSEL(QSPI_CSN, 0, 15)>;
			low-power-enable;
			bias-pull-up;
		};
	};

25LP-WP080D-040D-020D.pdf