uart_configure cause Stack overflow

[[email protected]]

when the code run to "uart_configure" function, the program cause Stack overflow 

	if (mdata.current_serial_speed != MDM_SPEED_WORK)
	{
		if (serial_cfg.baudrate != mdata.current_serial_speed)
		{
			serial_cfg.baudrate = mdata.current_serial_speed;
			// 停止接收数据
			uart_irq_rx_disable(MDM_UART_DEV);

			uart_configure(MDM_UART_DEV, &serial_cfg);
			// 开启接收数据
			uart_irq_rx_enable(MDM_UART_DEV);
		}

		snprintk(buf, sizeof(buf), "AT+IPR=%u", MDM_SPEED_WORK);

		ret = modem_cmd_send(&mctx.iface, &mctx.cmd_handler, NULL, 0U, buf,
							 &mdata.sem_response, K_MSEC(500));
		if (ret < 0)
		{
			LOG_ERR("Failed to send init commands!");
			goto error;
		}
		mdata.current_serial_speed = MDM_SPEED_WORK;
		serial_cfg.baudrate = MDM_SPEED_WORK;


		// 停止接收数据
		uart_irq_rx_disable(MDM_UART_DEV);

		uart_configure(MDM_UART_DEV, &serial_cfg);
		// 开启接收数据
		uart_irq_rx_enable(MDM_UART_DEV);

	}

[AHaug]

Hi,

1. Increasing the stacksize on the thread that triggers the overflow should remove this error
2. One tip is also to name your threads, if you haven't done so already. From the log it is currently called "Unknown". See https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-7-multithreaded-applications/topic/exercise-1-7/ for more

Kind regards,
Andreas

[[email protected]]

this code is called by startup, here is below

modem_init->modem_setup->uart_configure

what stack should be configured in this case?

[AHaug]

Hi,

1. Does the thread definition contain any parameters related to the stack size similar to the following?
   
2. Did you have a look at prj.conf in the links I sent you to see if you were able to spot how it's done there? Here's the github link https://github.com/NordicDeveloperAcademy/ncs-fund/tree/main/v2.x.x/lesson7 
3. If neither of these two are correct, you can use the Kconfig search with the term 'stack_size' to check if there are any configurations you're missing?
4. Could you also provide me your prj.conf?

Kind regards,
Andreas

[[email protected]]

I've seen the link you sent, I've also tried increasing the stack size in prj.conf, but stack overflow still happens.

After debugging, it was found that a stack overflow occurs whenever the “uart_configure (mctx.iface.dev, &serial_cfg)”  be called.After looking at the memory address, it looks like a stack overflow that occurred on the idle thread.

CONFIG_BT=y
CONFIG_BT_PERIPHERAL=y
CONFIG_BT_DEVICE_NAME="MS6KY"

CONFIG_BT_SMP=y
CONFIG_BT_FIXED_PASSKEY=y

CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=8192
CONFIG_LOG=y
CONFIG_LOG_PRINTK=y
CONFIG_LOG_MODE_IMMEDIATE=y
CONFIG_UART_CONSOLE=y

CONFIG_CMSIS_DSP=y
CONFIG_FPU=y
CONFIG_CMSIS_DSP_STATISTICS=y
CONFIG_NEWLIB_LIBC=y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF=y

CONFIG_JSON_LIBRARY=y

CONFIG_HEAP_MEM_POOL_SIZE=8192
CONFIG_SIMCOM_A7670C_DRIVER=y
CONFIG_MODEM_SIM_NUMBERS=y
CONFIG_MODEM_SIMCOM_A7670C_RX_STACK_SIZE=2048
CONFIG_NET_BUF=y
CONFIG_NTP_SERVER_ADDR="121.229.25.208"


CONFIG_NRFX_SAADC=y
CONFIG_NRFX_TIMER1=y

CONFIG_DATE_TIME=y

CONFIG_DEBUG_THREAD_INFO=n

CONFIG_DATE_TIME_NTP=n
# CONFIG_NETWORKING=n
# CONFIG_SDMMC_LOG_LEVEL_DBG=y

CONFIG_MAIN_STACK_SIZE=16384



CONFIG_FILE_SYSTEM=y
CONFIG_FAT_FILESYSTEM_ELM=y
CONFIG_FS_FATFS_LFN=y
CONFIG_DISK_DRIVER_SDMMC=y


CONFIG_PM=y
CONFIG_PM_DEVICE=y
CONFIG_PM_DEVICE_POWER_DOMAIN=y

CONFIG_MODBUS=y
CONFIG_MODBUS_ROLE_CLIENT=y

CONFIG_MODBUS_LOG_LEVEL_DBG=n


CONFIG_UART_INTERRUPT_DRIVEN=y
CONFIG_UART_LINE_CTRL=y


CONFIG_SETTINGS=y
CONFIG_NVS=y
CONFIG_FLASH=y
CONFIG_FLASH_PAGE_LAYOUT=y
CONFIG_FLASH_MAP=y
CONFIG_SETTINGS_NVS=y

CONFIG_SETTINGS=y
CONFIG_SETTINGS_RUNTIME=y


# CONFIG_RING_BUFFER=y

# CONFIG_DATA_CACHE_SIZE=16


CONFIG_LOG_USER_SETTINGS_LEVEL=0
# CONFIG_LOG_MAIN_LEVEL=3
CONFIG_NVS_LOG_LEVEL_OFF=y
CONFIG_SD_LOG_LEVEL_OFF=y

CONFIG_UART_USE_RUNTIME_CONFIGURE=y

[AHaug]

Hi,

Does the overflow occur when you have a main stack size of 16384? If so then I suspect you have a memory leak somewhere in your firmware unless it is related to having heap or workqueue stack size set too small. I see they are 8192, which should also be more than sufficient. 

Could you explain more about exactly what your application should do since you have set these sizes so large?

Kind regards,
Andreas

[[email protected]]

I've also tried increasing the size of the main stack, and I have also tried increasing the size of the workqueue stack, and the same phenomenon still occurs. I think it should not be a problem with the stack, or a stack overflow when changing the baud rate from 115200 to 230400 at runtime, as long as the baud rate is not modified, there is no problem