BLE OTA DFU using external flash

[allenyang]

I'm using the NCS 2.5.2 sdk and nrf 5340 with 7002, and I want to do BLE OTA DFU using external flash.

I've found this guide Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com), and successfully  done BLE OTA DFU using internal flash, just add the commands below,

#Enable MCUBOOT bootloader build in the application

CONFIG_BOOTLOADER_MCUBOOT=y

#Include MCUMGR and the dependencies in the build

CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU=y

but I don't know how to do with external flash, I've tried looking at main.c in mcuboot, and I didn't find where to modify the code.

[Sigurd Hellesvik]

Hi,

See https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/ instead. This is up to date with the newest nRF Connect SDK.

Regards,
Sigurd Hellesvik

[allenyang]

Hi, when I add the config to the prj.conf and set the devicetree of the external flash, it has few error occur.

prj.conf

#config RTT
CONFIG_LOG=y
CONFIG_LOG_PRINTK=y
# CONFIG_LOG_MODE_DEFERRED=y
CONFIG_UART_CONSOLE=n
CONFIG_USE_SEGGER_RTT=y
CONFIG_RTT_CONSOLE=y
CONFIG_LOG_BACKEND_RTT=y
CONFIG_LOG_BACKEND_UART=n

CONFIG_SEGGER_RTT_BUFFER_SIZE_UP=4096
CONFIG_LOG_BUFFER_SIZE=4096

CONFIG_BT=y
CONFIG_BT_PERIPHERAL=y
CONFIG_BT_DEVICE_NAME="test 0422"
CONFIG_BT_DEVICE_APPEARANCE=833
CONFIG_BT_MAX_CONN=1
CONFIG_BT_MAX_PAIRED=1
CONFIG_HW_ID_LIBRARY=y
CONFIG_HW_ID_LIBRARY_SOURCE_BLE_MAC=y


# # Enable the NUS service
# CONFIG_BT_NUS=y

# # Enable bonding
# CONFIG_BT_SETTINGS=y
# CONFIG_FLASH=y
# CONFIG_FLASH_PAGE_LAYOUT=y
# CONFIG_FLASH_MAP=y
# CONFIG_NVS=y
# CONFIG_SETTINGS=y

#ota
#Enable MCUBOOT bootloader build in the application
CONFIG_BOOTLOADER_MCUBOOT=y
#Include MCUMGR and the dependencies in the build
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU=y


CONFIG_NORDIC_QSPI_NOR=n
CONFIG_SPI=y
CONFIG_SPI_NOR=y
CONFIG_SPI_NOR_FLASH_LAYOUT_PAGE_SIZE=4096

# If you don't add this when setting CONFIG_SPI=y, you'll get a lot of undefined references from the nrfx spim driver
# E.G. "undefined reference to `z_impl_k_sleep'"
CONFIG_MULTITHREADING=y
CONFIG_SPI_NOR_SFDP_DEVICETREE=y
CONFIG_PM_OVERRIDE_EXTERNAL_DRIVER_CHECK=y
CONFIG_PM_EXTERNAL_FLASH_MCUBOOT_SECONDARY=y

# Disable internal DCDC
CONFIG_BOARD_ENABLE_DCDC_APP=n
CONFIG_BOARD_ENABLE_DCDC_NET=n
CONFIG_BOARD_ENABLE_DCDC_HV=n

# Use internal capacitor for 32M xtal and set capacitor value to 8.5pF 
# (ranging from 7.0 pF to 20.0 pF in 0.5 pF steps
# can be enabled on pins XC1 and XC2. This option specifies doubled
# capacitance value for the two capacitors. Set it to 14 to get 7.0 pF
# for each capacitor, 15 to get 7.5 pF, and so on.
# )
CONFIG_SOC_HFXO_CAP_INTERNAL=y
CONFIG_SOC_HFXO_CAP_INT_VALUE_X2=17
 
#  Use internal capacitor for 32k xtal and set capacitor value to 7pF 
# (only 4 options of internal capacitor value settings for 32k xtal
#   -INT_6PF
#   -INT_7PF
#   -INT_9PF
#   - USE external capacitor)
CONFIG_SOC_ENABLE_LFXO=y
CONFIG_SOC_LFXO_CAP_INT_7PF=y

device tree

    chosen {

        zephyr,sram = &sram0_image;

        zephyr,flash = &flash0;

        zephyr,code-partition = &slot0_partition;

        zephyr,sram-secure-partition = &sram0_s;

        zephyr,sram-non-secure-partition = &sram0_ns;

        nordic,pm-ext-flash = &mx25l3233;

    };

&spi3 {

    compatible = "nordic,nrf-spim";

    status = "okay";

    pinctrl-0 = <&spi3_default>;

    pinctrl-1 = <&spi3_sleep>;

    pinctrl-names = "default", "sleep";

    cs-gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;

    mx25l3233: mx25l3233@0 {

            compatible = "jedec,spi-nor";

            reg = <0>;

            spi-max-frequency = <8000000>;

            label = "extflash";

            jedec-id = [ C2 20 16  ];

            sfdp-bfp = [ E5 20 F1 FF FF FF FF 01 44 EB 08 6B 08 3B 04 BB EE FF 00 00 FF 00 00 FF FF 00 00 FF 0C 20 0F 52 10 D8 00 FF 00 36 50 26 9E F9 77 64 FE CF FF FF FF FF FF FF  ];

            size = <33554432>;

            // has-dpd;

            // t-enter-dpd = <10000>;

            // t-exit-dpd = <35000>;

    };

};

error message

      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:42: note: in expansion of macro 'DT_DRV_INST'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:77:30: note: in expansion of macro 'DT_INST_PROP'
   77 | #define INST_0_SCK_FREQUENCY DT_INST_PROP(0, sck_frequency)
      |                              ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:82:14: note: in expansion of macro 'INST_0_SCK_FREQUENCY'
   82 | BUILD_ASSERT(INST_0_SCK_FREQUENCY >= (NRF_QSPI_BASE_CLOCK_FREQ / 16),
      |              ^~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: expression in static assertion is not an integer
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:614:32: note: in expansion of macro 'DT_CAT3'
  614 | #define DT_PROP(node_id, prop) DT_CAT3(node_id, _P_, prop)
      |                                ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:34: note: in expansion of macro 'DT_PROP'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                  ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:42: note: in expansion of macro 'DT_DRV_INST'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:77:30: note: in expansion of macro 'DT_INST_PROP'
   77 | #define INST_0_SCK_FREQUENCY DT_INST_PROP(0, sck_frequency)
      |                              ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:82:14: note: in expansion of macro 'INST_0_SCK_FREQUENCY'
   82 | BUILD_ASSERT(INST_0_SCK_FREQUENCY >= (NRF_QSPI_BASE_CLOCK_FREQ / 16),
      |              ^~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: 'DT_N_INST_0_nordic_qspi_nor_P_cpol' undeclared here (not in a function); did you mean 'DT_N_INST_0_nordic_mbox_nrf_ipc'?
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:614:32: note: in expansion of macro 'DT_CAT3'
  614 | #define DT_PROP(node_id, prop) DT_CAT3(node_id, _P_, prop)
      |                                ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:34: note: in expansion of macro 'DT_PROP'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                  ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:42: note: in expansion of macro 'DT_DRV_INST'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:136:14: note: in expansion of macro 'DT_INST_PROP'
  136 | BUILD_ASSERT(DT_INST_PROP(0, cpol) == DT_INST_PROP(0, cpha),
      |              ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: 'DT_N_INST_0_nordic_qspi_nor_P_cpha' undeclared here (not in a function); did you mean 'DT_N_INST_0_nordic_mbox_nrf_ipc'?
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:614:32: note: in expansion of macro 'DT_CAT3'
  614 | #define DT_PROP(node_id, prop) DT_CAT3(node_id, _P_, prop)
      |                                ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:34: note: in expansion of macro 'DT_PROP'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                  ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:42: note: in expansion of macro 'DT_DRV_INST'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:136:39: note: in expansion of macro 'DT_INST_PROP'
  136 | BUILD_ASSERT(DT_INST_PROP(0, cpol) == DT_INST_PROP(0, cpha),
      |                                       ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: expression in static assertion is not an integer
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:614:32: note: in expansion of macro 'DT_CAT3'
  614 | #define DT_PROP(node_id, prop) DT_CAT3(node_id, _P_, prop)
      |                                ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:34: note: in expansion of macro 'DT_PROP'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                  ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:42: note: in expansion of macro 'DT_DRV_INST'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:136:14: note: in expansion of macro 'DT_INST_PROP'
  136 | BUILD_ASSERT(DT_INST_PROP(0, cpol) == DT_INST_PROP(0, cpha),
      |              ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:144:28: error: 'JESD216_DW15_QER_VAL_DT_N_INST_0_nordic_qspi_nor_P_quad_enable_requirements_STRING_TOKEN' undeclared here (not in a function)
  144 | #define INST_0_QER _CONCAT(JESD216_DW15_QER_VAL_, \
      |                            ^~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:160:15: note: in expansion of macro 'IS_EQUAL'
  160 | BUILD_ASSERT((IS_EQUAL(INST_0_QER, JESD216_DW15_QER_VAL_NONE)
      |               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/common.h:133:23: note: in expansion of macro '_DO_CONCAT'
  133 | #define _CONCAT(x, y) _DO_CONCAT(x, y)
      |                       ^~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:144:20: note: in expansion of macro '_CONCAT'
  144 | #define INST_0_QER _CONCAT(JESD216_DW15_QER_VAL_, \
      |                    ^~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:160:24: note: in expansion of macro 'INST_0_QER'
  160 | BUILD_ASSERT((IS_EQUAL(INST_0_QER, JESD216_DW15_QER_VAL_NONE)
      |                        ^~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:160:14: error: expression in static assertion is not an integer
  160 | BUILD_ASSERT((IS_EQUAL(INST_0_QER, JESD216_DW15_QER_VAL_NONE)
      |              ^
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c: In function 'qspi_nor_init':
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: 'DT_N_INST_0_nordic_qspi_nor_BUS_IRQ_IDX_0_VAL_priority' undeclared (first use in this function)
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/arch/arm/aarch32/irq.h:128:9: note: in expansion of macro '_CHECK_PRIO'
  128 |         _CHECK_PRIO(priority_p, flags_p) \
      |         ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/irq.h:49:9: note: in expansion of macro 'ARCH_IRQ_CONNECT'
   49 |         ARCH_IRQ_CONNECT(irq_p, priority_p, isr_p, isr_param_p, flags_p)
      |         ^~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:9: note: in expansion of macro 'IRQ_CONNECT'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |         ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:2383:9: note: in expansion of macro 'DT_CAT5'
 2383 |         DT_CAT5(node_id, _IRQ_IDX_, idx, _VAL_, cell)
      |         ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:2410:31: note: in expansion of macro 'DT_IRQ_BY_IDX'
 2410 | #define DT_IRQ(node_id, cell) DT_IRQ_BY_IDX(node_id, 0, cell)
      |                               ^~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:41: note: in expansion of macro 'DT_IRQ'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |                                         ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3190:25: note: in expansion of macro 'DT_CAT'
 3190 | #define DT_BUS(node_id) DT_CAT(node_id, _BUS)
      |                         ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:27: note: in expansion of macro 'DT_BUS'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                           ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:34: note: in expansion of macro 'DT_DRV_INST'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                                  ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:140:19: note: in expansion of macro 'DT_INST_BUS'
  140 | #define QSPI_NODE DT_INST_BUS(0)
      |                   ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:48: note: in expansion of macro 'QSPI_NODE'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |                                                ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: note: each undeclared identifier is reported only once for each function it appears in
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/arch/arm/aarch32/irq.h:128:9: note: in expansion of macro '_CHECK_PRIO'
  128 |         _CHECK_PRIO(priority_p, flags_p) \
      |         ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/irq.h:49:9: note: in expansion of macro 'ARCH_IRQ_CONNECT'
   49 |         ARCH_IRQ_CONNECT(irq_p, priority_p, isr_p, isr_param_p, flags_p)
      |         ^~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:9: note: in expansion of macro 'IRQ_CONNECT'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |         ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:2383:9: note: in expansion of macro 'DT_CAT5'
 2383 |         DT_CAT5(node_id, _IRQ_IDX_, idx, _VAL_, cell)
      |         ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:2410:31: note: in expansion of macro 'DT_IRQ_BY_IDX'
 2410 | #define DT_IRQ(node_id, cell) DT_IRQ_BY_IDX(node_id, 0, cell)
      |                               ^~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:41: note: in expansion of macro 'DT_IRQ'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |                                         ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3190:25: note: in expansion of macro 'DT_CAT'
 3190 | #define DT_BUS(node_id) DT_CAT(node_id, _BUS)
      |                         ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:27: note: in expansion of macro 'DT_BUS'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                           ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:34: note: in expansion of macro 'DT_DRV_INST'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                                  ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:140:19: note: in expansion of macro 'DT_INST_BUS'
  140 | #define QSPI_NODE DT_INST_BUS(0)
      |                   ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:48: note: in expansion of macro 'QSPI_NODE'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |                                                ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/arch/arm/aarch32/irq.h:105:22: error: expression in static assertion is not an integer
  105 |         BUILD_ASSERT(((flags_p & IRQ_ZERO_LATENCY) && \
      |                      ^
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/arch/arm/aarch32/irq.h:128:9: note: in expansion of macro '_CHECK_PRIO'
  128 |         _CHECK_PRIO(priority_p, flags_p) \
      |         ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/irq.h:49:9: note: in expansion of macro 'ARCH_IRQ_CONNECT'
   49 |         ARCH_IRQ_CONNECT(irq_p, priority_p, isr_p, isr_param_p, flags_p)
      |         ^~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:9: note: in expansion of macro 'IRQ_CONNECT'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |         ^~~~~~~~~~~
In file included from C:/ncs/v2.5.2/zephyr/include/zephyr/arch/arm/aarch32/irq.h:19,
                 from C:/ncs/v2.5.2/zephyr/include/zephyr/arch/arm/aarch32/arch.h:27,
                 from C:/ncs/v2.5.2/zephyr/include/zephyr/arch/cpu.h:19,
                 from C:/ncs/v2.5.2/zephyr/include/zephyr/kernel_includes.h:33,
                 from C:/ncs/v2.5.2/zephyr/include/zephyr/kernel.h:17,
                 from C:/ncs/v2.5.2/zephyr/include/zephyr/pm/device.h:11,
                 from C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:12:
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: 'DT_N_INST_0_nordic_qspi_nor_BUS_IRQ_IDX_0_VAL_irq' undeclared (first use in this function)
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sw_isr_table.h:77:26: note: in definition of macro 'Z_ISR_DECLARE'
   77 |                         {irq, flags, (void *)&func, (const void *)param}
      |                          ^~~
C:/ncs/v2.5.2/zephyr/include/zephyr/irq.h:49:9: note: in expansion of macro 'ARCH_IRQ_CONNECT'
   49 |         ARCH_IRQ_CONNECT(irq_p, priority_p, isr_p, isr_param_p, flags_p)
      |         ^~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:9: note: in expansion of macro 'IRQ_CONNECT'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |         ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:2383:9: note: in expansion of macro 'DT_CAT5'
 2383 |         DT_CAT5(node_id, _IRQ_IDX_, idx, _VAL_, cell)
      |         ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:2410:31: note: in expansion of macro 'DT_IRQ_BY_IDX'
 2410 | #define DT_IRQ(node_id, cell) DT_IRQ_BY_IDX(node_id, 0, cell)
      |                               ^~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:2422:26: note: in expansion of macro 'DT_IRQ'
 2422 | #define DT_IRQN(node_id) DT_IRQ(node_id, irq)
      |                          ^~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:21: note: in expansion of macro 'DT_IRQN'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |                     ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3190:25: note: in expansion of macro 'DT_CAT'
 3190 | #define DT_BUS(node_id) DT_CAT(node_id, _BUS)
      |                         ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:27: note: in expansion of macro 'DT_BUS'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                           ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:34: note: in expansion of macro 'DT_DRV_INST'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                                  ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:140:19: note: in expansion of macro 'DT_INST_BUS'
  140 | #define QSPI_NODE DT_INST_BUS(0)
      |                   ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1242:29: note: in expansion of macro 'QSPI_NODE'
 1242 |         IRQ_CONNECT(DT_IRQN(QSPI_NODE), DT_IRQ(QSPI_NODE, priority),
      |                             ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c: At top level:
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1262:29: error: 'INST_0_BYTES' undeclared here (not in a function); did you mean 'INST_0_QER'?
 1262 | #define LAYOUT_PAGES_COUNT (INST_0_BYTES / \
      |                             ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1266:15: note: in expansion of macro 'LAYOUT_PAGES_COUNT'
 1266 |               LAYOUT_PAGES_COUNT)
      |               ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1265:14: error: expression in static assertion is not an integer
 1265 | BUILD_ASSERT((CONFIG_NORDIC_QSPI_NOR_FLASH_LAYOUT_PAGE_SIZE *
      |              ^
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:51: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                   ^~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: expected ')' before 'DT_N_INST_0_nordic_qspi_nor_BUS_PATH'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:60: note: in definition of macro 'BUILD_ASSERT'
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                            ^~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:495:31: note: in expansion of macro 'DT_CAT'
  495 | #define DT_NODE_PATH(node_id) DT_CAT(node_id, _PATH)
      |                               ^~~~~~
c:\ncs\v2.5.2\zephyr\soc\arm\nordic_nrf\common\soc_nrf_common.h:191:22: note: in expansion of macro 'DT_NODE_PATH'
  191 |                      DT_NODE_PATH(node_id) " defined without sleep state")
      |                      ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1492:1: note: in expansion of macro 'NRF_DT_CHECK_NODE_HAS_PINCTRL_SLEEP'
 1492 | NRF_DT_CHECK_NODE_HAS_PINCTRL_SLEEP(QSPI_NODE);
      | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3190:25: note: in expansion of macro 'DT_CAT'
 3190 | #define DT_BUS(node_id) DT_CAT(node_id, _BUS)
      |                         ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:27: note: in expansion of macro 'DT_BUS'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                           ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:34: note: in expansion of macro 'DT_DRV_INST'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                                  ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:140:19: note: in expansion of macro 'DT_INST_BUS'
  140 | #define QSPI_NODE DT_INST_BUS(0)
      |                   ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1492:37: note: in expansion of macro 'QSPI_NODE'
 1492 | NRF_DT_CHECK_NODE_HAS_PINCTRL_SLEEP(QSPI_NODE);
      |                                     ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:81:50: note: to match this '('
   81 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)
      |                                                  ^
c:\ncs\v2.5.2\zephyr\soc\arm\nordic_nrf\common\soc_nrf_common.h:189:9: note: in expansion of macro 'BUILD_ASSERT'
  189 |         BUILD_ASSERT(!IS_ENABLED(CONFIG_PM_DEVICE) ||                          \
      |         ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1492:1: note: in expansion of macro 'NRF_DT_CHECK_NODE_HAS_PINCTRL_SLEEP'
 1492 | NRF_DT_CHECK_NODE_HAS_PINCTRL_SLEEP(QSPI_NODE);
      | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util.h:17:
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:241:51: error: expected ')' before '(' token
  241 |                      Z_PINCTRL_STATE_PINS_DEFINE, (;), node_id);               \
      |                                                   ^
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_macro.h:418:69: note: in definition of macro 'LISTIFY'
  418 | #define LISTIFY(LEN, F, sep, ...) UTIL_CAT(Z_UTIL_LISTIFY_, LEN)(F, sep, __VA_ARGS__)
      |                                                                     ^~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1494:1: note: in expansion of macro 'PINCTRL_DT_DEFINE'
 1494 | PINCTRL_DT_DEFINE(QSPI_NODE);
      | ^~~~~~~~~~~~~~~~~
In file included from C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_macro.h:34:
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_macro.h:418:44: warning: implicit declaration of function 'Z_UTIL_LISTIFY_DT_N_INST_0_nordic_qspi_nor_BUS_PINCTRL_NUM' [-Wimplicit-function-declaration]
  418 | #define LISTIFY(LEN, F, sep, ...) UTIL_CAT(Z_UTIL_LISTIFY_, LEN)(F, sep, __VA_ARGS__)
      |                                            ^~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:105:36: note: in definition of macro 'UTIL_PRIMITIVE_CAT'
  105 | #define UTIL_PRIMITIVE_CAT(a, ...) a##__VA_ARGS__
      |                                    ^
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_macro.h:418:35: note: in expansion of macro 'UTIL_CAT'
  418 | #define LISTIFY(LEN, F, sep, ...) UTIL_CAT(Z_UTIL_LISTIFY_, LEN)(F, sep, __VA_ARGS__)
      |                                   ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:172:17: note: in expansion of macro 'LISTIFY'
  172 |                 LISTIFY(DT_NUM_PINCTRL_STATES(node_id),                        \
      |                 ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:242:9: note: in expansion of macro 'Z_PINCTRL_STATES_DEFINE'
  242 |         Z_PINCTRL_STATES_DEFINE(node_id)                                       \
      |         ^~~~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1494:1: note: in expansion of macro 'PINCTRL_DT_DEFINE'
 1494 | PINCTRL_DT_DEFINE(QSPI_NODE);
      | ^~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:173:30: error: 'Z_PINCTRL_STATE_INIT' undeclared here (not in a function)
  173 |                              Z_PINCTRL_STATE_INIT, (,), node_id)               \
      |                              ^~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_macro.h:418:66: note: in definition of macro 'LISTIFY'
  418 | #define LISTIFY(LEN, F, sep, ...) UTIL_CAT(Z_UTIL_LISTIFY_, LEN)(F, sep, __VA_ARGS__)
      |                                                                  ^
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:242:9: note: in expansion of macro 'Z_PINCTRL_STATES_DEFINE'
  242 |         Z_PINCTRL_STATES_DEFINE(node_id)                                       \
      |         ^~~~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1494:1: note: in expansion of macro 'PINCTRL_DT_DEFINE'
 1494 | PINCTRL_DT_DEFINE(QSPI_NODE);
      | ^~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:173:53: error: expected expression before ',' token
  173 |                              Z_PINCTRL_STATE_INIT, (,), node_id)               \
      |                                                     ^
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_macro.h:418:69: note: in definition of macro 'LISTIFY'
  418 | #define LISTIFY(LEN, F, sep, ...) UTIL_CAT(Z_UTIL_LISTIFY_, LEN)(F, sep, __VA_ARGS__)
      |                                                                     ^~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:242:9: note: in expansion of macro 'Z_PINCTRL_STATES_DEFINE'
  242 |         Z_PINCTRL_STATES_DEFINE(node_id)                                       \
      |         ^~~~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1494:1: note: in expansion of macro 'PINCTRL_DT_DEFINE'
 1494 | PINCTRL_DT_DEFINE(QSPI_NODE);
      | ^~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:173:53: warning: left-hand operand of comma expression has no effect [-Wunused-value]
  173 |                              Z_PINCTRL_STATE_INIT, (,), node_id)               \
      |                                                     ^
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_macro.h:418:69: note: in definition of macro 'LISTIFY'
  418 | #define LISTIFY(LEN, F, sep, ...) UTIL_CAT(Z_UTIL_LISTIFY_, LEN)(F, sep, __VA_ARGS__)
      |                                                                     ^~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:242:9: note: in expansion of macro 'Z_PINCTRL_STATES_DEFINE'
  242 |         Z_PINCTRL_STATES_DEFINE(node_id)                                       \
      |         ^~~~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1494:1: note: in expansion of macro 'PINCTRL_DT_DEFINE'
 1494 | PINCTRL_DT_DEFINE(QSPI_NODE);
      | ^~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: 'DT_N_INST_0_nordic_qspi_nor_BUS' undeclared here (not in a function); did you mean 'DT_N_INST_0_nordic_mbox_nrf_ipc'?
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_macro.h:418:74: note: in definition of macro 'LISTIFY'
  418 | #define LISTIFY(LEN, F, sep, ...) UTIL_CAT(Z_UTIL_LISTIFY_, LEN)(F, sep, __VA_ARGS__)
      |                                                                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:242:9: note: in expansion of macro 'Z_PINCTRL_STATES_DEFINE'
  242 |         Z_PINCTRL_STATES_DEFINE(node_id)                                       \
      |         ^~~~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1494:1: note: in expansion of macro 'PINCTRL_DT_DEFINE'
 1494 | PINCTRL_DT_DEFINE(QSPI_NODE);
      | ^~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3190:25: note: in expansion of macro 'DT_CAT'
 3190 | #define DT_BUS(node_id) DT_CAT(node_id, _BUS)
      |                         ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:27: note: in expansion of macro 'DT_BUS'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                           ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3836:34: note: in expansion of macro 'DT_DRV_INST'
 3836 | #define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst))
      |                                  ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:140:19: note: in expansion of macro 'DT_INST_BUS'
  140 | #define QSPI_NODE DT_INST_BUS(0)
      |                   ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1494:19: note: in expansion of macro 'QSPI_NODE'
 1494 | PINCTRL_DT_DEFINE(QSPI_NODE);
      |                   ^~~~~~~~~
In file included from C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/gcc.h:92:
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:101:17: error: '__pinctrl_dev_config__device_dts_ord_DT_N_INST_0_nordic_qspi_nor_BUS_ORD' undeclared here (not in a function); did you mean '__pinctrl_states__device_dts_ord_DT_N_INST_0_nordic_qspi_nor_BUS_ORD'?
  101 |         _CONCAT(__pinctrl_dev_config, DEVICE_DT_NAME_GET(node_id))
      |                 ^~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/common.h:132:26: note: in definition of macro '_DO_CONCAT'
  132 | #define _DO_CONCAT(x, y) x ## y
      |                          ^
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:101:9: note: in expansion of macro '_CONCAT'
  101 |         _CONCAT(__pinctrl_dev_config, DEVICE_DT_NAME_GET(node_id))
      |         ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:262:45: note: in expansion of macro 'Z_PINCTRL_DEV_CONFIG_NAME'
  262 | #define PINCTRL_DT_DEV_CONFIG_GET(node_id) &Z_PINCTRL_DEV_CONFIG_NAME(node_id)
      |                                             ^~~~~~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1499:17: note: in expansion of macro 'PINCTRL_DT_DEV_CONFIG_GET'
 1499 |         .pcfg = PINCTRL_DT_DEV_CONFIG_GET(QSPI_NODE),
      |                 ^~~~~~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: 'DT_N_INST_0_nordic_qspi_nor_P_address_size_32' undeclared here (not in a function)
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:4231:29: note: in definition of macro 'DT_CAT3'
 4231 | #define DT_CAT3(a1, a2, a3) a1 ## a2 ## a3
      |                             ^~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:34: note: in expansion of macro 'DT_PROP'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                  ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:42: note: in expansion of macro 'DT_DRV_INST'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1511:29: note: in expansion of macro 'DT_INST_PROP'
 1511 |                 .addrmode = DT_INST_PROP(0, address_size_32)
      |                             ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: 'DT_N_INST_0_nordic_qspi_nor_P_sck_delay' undeclared here (not in a function)
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:4231:29: note: in definition of macro 'DT_CAT3'
 4231 | #define DT_CAT3(a1, a2, a3) a1 ## a2 ## a3
      |                             ^~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:34: note: in expansion of macro 'DT_PROP'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                  ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:42: note: in expansion of macro 'DT_DRV_INST'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1517:30: note: in expansion of macro 'DT_INST_PROP'
 1517 |                 .sck_delay = DT_INST_PROP(0, sck_delay),
      |                              ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: 'DT_N_INST_0_nordic_qspi_nor_P_jedec_id' undeclared here (not in a function); did you mean 'DT_N_INST_0_nordic_nrf_qdec'?
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:4231:29: note: in definition of macro 'DT_CAT3'
 4231 | #define DT_CAT3(a1, a2, a3) a1 ## a2 ## a3
      |                             ^~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:34: note: in expansion of macro 'DT_PROP'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                  ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3450:42: note: in expansion of macro 'DT_DRV_INST'
 3450 | #define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop)
      |                                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1522:15: note: in expansion of macro 'DT_INST_PROP'
 1522 |         .id = DT_INST_PROP(0, jedec_id),
      |               ^~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:40: error: 'DT_N_INST_0_nordic_qspi_nor_FULL_NAME' undeclared here (not in a function)
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                                        ^~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/device.h:892:25: note: in definition of macro 'Z_DEVICE_INIT'
  892 |                 .name = name_,                                                 \
      |                         ^~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/device.h:981:9: note: in expansion of macro 'Z_DEVICE_BASE_DEFINE'
  981 |         Z_DEVICE_BASE_DEFINE(node_id, dev_id, name, pm, data, config, level,   \
      |         ^~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/device.h:180:9: note: in expansion of macro 'Z_DEVICE_DEFINE'
  180 |         Z_DEVICE_DEFINE(node_id, Z_DEVICE_DT_DEV_ID(node_id),                  \
      |         ^~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:69:53: note: in expansion of macro '__DEBRACKET'
   69 | #define __GET_ARG2_DEBRACKET(ignore_this, val, ...) __DEBRACKET val
      |                                                     ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:64:9: note: in expansion of macro '__GET_ARG2_DEBRACKET'
   64 |         __GET_ARG2_DEBRACKET(one_or_two_args _if_code, _else_code)
      |         ^~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:59:9: note: in expansion of macro '__COND_CODE'
   59 |         __COND_CODE(_XXXX##_flag, _if_1_code, _else_code)
      |         ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_macro.h:180:9: note: in expansion of macro 'Z_COND_CODE_1'
  180 |         Z_COND_CODE_1(_flag, _if_1_code, _else_code)
      |         ^~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:777:9: note: in expansion of macro 'COND_CODE_1'
  777 |         COND_CODE_1(DT_NODE_HAS_PROP(node_id, prop), \
      |         ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/device.h:146:9: note: in expansion of macro 'DT_PROP_OR'
  146 |         DT_PROP_OR(node_id, label, DT_NODE_FULL_NAME(node_id))
      |         ^~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:521:36: note: in expansion of macro 'DT_CAT'
  521 | #define DT_NODE_FULL_NAME(node_id) DT_CAT(node_id, _FULL_NAME)
      |                                    ^~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/device.h:146:36: note: in expansion of macro 'DT_NODE_FULL_NAME'
  146 |         DT_PROP_OR(node_id, label, DT_NODE_FULL_NAME(node_id))
      |                                    ^~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/device.h:181:25: note: in expansion of macro 'DEVICE_DT_NAME'
  181 |                         DEVICE_DT_NAME(node_id), init_fn, pm, data, config,    \
      |                         ^~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/device.h:195:9: note: in expansion of macro 'DEVICE_DT_DEFINE'
  195 |         DEVICE_DT_DEFINE(DT_DRV_INST(inst), __VA_ARGS__)
      |         ^~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/sys/util_internal.h:104:26: note: in expansion of macro 'UTIL_PRIMITIVE_CAT'
  104 | #define UTIL_CAT(a, ...) UTIL_PRIMITIVE_CAT(a, __VA_ARGS__)
      |                          ^~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:333:31: note: in expansion of macro 'UTIL_CAT'
  333 | #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
      |                               ^~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/devicetree.h:3248:27: note: in expansion of macro 'DT_INST'
 3248 | #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
      |                           ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/device.h:195:26: note: in expansion of macro 'DT_DRV_INST'
  195 |         DEVICE_DT_DEFINE(DT_DRV_INST(inst), __VA_ARGS__)
      |                          ^~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1527:1: note: in expansion of macro 'DEVICE_DT_INST_DEFINE'
 1527 | DEVICE_DT_INST_DEFINE(0, qspi_nor_init, PM_DEVICE_DT_INST_GET(0),
      | ^~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:110:17: warning: '__pinctrl_states__device_dts_ord_DT_N_INST_0_nordic_qspi_nor_BUS_ORD' defined but not used [-Wunused-const-variable=]
  110 |         _CONCAT(__pinctrl_states, DEVICE_DT_NAME_GET(node_id))
      |                 ^~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/toolchain/common.h:132:26: note: in definition of macro '_DO_CONCAT'
  132 | #define _DO_CONCAT(x, y) x ## y
      |                          ^
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:110:9: note: in expansion of macro '_CONCAT'
  110 |         _CONCAT(__pinctrl_states, DEVICE_DT_NAME_GET(node_id))
      |         ^~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:171:9: note: in expansion of macro 'Z_PINCTRL_STATES_NAME'
  171 |         Z_PINCTRL_STATES_NAME(node_id)[] = {                                   \
      |         ^~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/include/zephyr/drivers/pinctrl.h:242:9: note: in expansion of macro 'Z_PINCTRL_STATES_DEFINE'
  242 |         Z_PINCTRL_STATES_DEFINE(node_id)                                       \
      |         ^~~~~~~~~~~~~~~~~~~~~~~
C:/ncs/v2.5.2/zephyr/drivers/flash/nrf_qspi_nor.c:1494:1: note: in expansion of macro 'PINCTRL_DT_DEFINE'
 1494 | PINCTRL_DT_DEFINE(QSPI_NODE);
      | ^~~~~~~~~~~~~~~~~
[179/281] Linking C static library zephyr\libzephyr.a
FAILED: modules/mcuboot/mcuboot_subimage-prefix/src/mcuboot_subimage-stamp/mcuboot_subimage-build mcuboot/zephyr/zephyr.hex mcuboot/zephyr/zephyr.elf 

[allenyang]

       I've added this line in the code,

"printk("build time: " __DATE__ " " __TIME__ "\n")" to check the build time.

      and add  "printk("test\n")" to make the differences easy to see.

[Sigurd Hellesvik]

Hmm,

Let us take a step back then:
Can you test this sample for the nRF5340DK and see if that works?

[allenyang]

"Can you test this sample for the nRF5340DK and see if that works?"

Yes, it works and can see the change after ota.

I think I know what's the problem, last time I said it is failed and stuck in  "sending the request failed", the reason is I'm doing spi transmit simultaneously in my application , so I commented out the line,

but after this, it has other problems,

it sometimes uploaded completely but when I checked the log it's still old application.

and sometimes the state said "There is no free slot to place the image.""  

[Sigurd Hellesvik]

allenyang said:

and sometimes the state said "There is no free slot to place the image."

Could you use the nRF Logger app to see what more logs come before this error?

allenyang said:

it sometimes uploaded completely but when I checked the log it's still old application.

If you enable advanced settings in the Device Manager App, you can use an "image list" command. What does that show when you still load the old app?

[allenyang]

I have new observations.

After the application flash to the board, do the first build of the image and do ota to the board, it always run normally on Device Manager App and it states Upload Complete but it's still a old app. And use the same file to OTA again, it still states Upload Complete but it still get nothing change. 

After that, when do the second or third ...build of the image, and do ota, it  will state "There is no free slot to place the image."

It seems it has something wrong when doing first OTA.

"If you enable advanced settings in the Device Manager App, you can use an "image list" command. What does that show when you still load the old app?"

"Could you use the nRF Logger app to see what more logs come before this error?"

Does it have an IOS version?