I2C interface with HTU21D using nrf51822

Question

HTU21D.rar hello there i am interfacing HTU21D with nrf51822. i am reading temperature and humidty from HTU21D. humidty register is E5. and temperature register is E3. now my problem is that when i am trying to read only humidity it gives me correct value. when i am trying to read only temperature it gives me wrong value.when i am trying to read both temperature and humidity i am getting both wrong value. 
 I have uploaded code here. can you tell me what is problem here?? is there any problem in writing i2c driver??

Fredrik Sundt Brynhildsvoll · Accepted Answer

Edit: Added a function that read the temperature. 
 Is this question resolved?
I have actually implemented this sensor (HTU21D) in one of my projects, so I should be able to help. 
 First of all: I would recommend you to use the function nrf_delay_ms() to delay the microcontroller. To use this you must include "nrf_delay.h" 
 You are writing to the registers 0xE3 and 0xE5. As stated in the datasheet of HTU21D this is "hold master" mode.
When using a hold master mode the argument xfer_pending must be set to 'true':
nrf_drv_twi_tx(p_twi_master,slave_addr, &reg_addr,1, true ); 
 I have rewritten your function for reading the humidity. I cannot test it right now, but I believe it should work. 
 void HTU21D_Humidity1(int *r) {
ret_code_t ret_code;
uint8_t htu21d_address = 0x40; //7 bit address of HTU21D
uint8_t trigger_humidiy_no_hold_master = 0xF5; //Address to humidity reading with no hold of twi lines
uint8_t returned_over_I2C[3] = {0,0,0}; //Array to hold data

ret_code = nrf_drv_twi_tx(p_twi_master, htu21d_address, &trigger_humidiy_no_hold_master, 1, true);//Writing 0xE5 to HTU21D tell the sensor to start humidity readings and hold the master
nrf_delay_ms(50);//Delay 50 ms, which is the maximum measurement time stated in datasheet
ret_code = nrf_drv_twi_rx(p_twi_master, htu21d_address, returned_over_I2C, 3, false); //Get raw humidity data
nrf_delay_ms(5);
//Calculate humidity
uint16_t rawHumidity = ((unsigned int) returned_over_I2C[0] << 8) | (unsigned int) returned_over_I2C[1];
float tempRH = rawHumidity / (float)65536; //2^16 = 65536
float rh = -6 + (125 * tempRH); //From page 14 in datasheet
*r = (int)(rh); // this could be change to (int)(rh*10), then one decimal of the humidity data will be kept (but 34.5 = 345 ) 
}
 
 Function that read the temperature: 
 void HTU21D_Temperature1(float *r){
ret_code_t ret_code;
uint8_t htu21d_address = 0x40; //7 bit address of HTU21D
uint8_t trigger_temperature_no_hold_master = 0xE3; //Address to temperature reading with no hold of twi lines
uint8_t returned_over_I2C[3] = {0,0,0}; //Array to hold data

ret_code = nrf_drv_twi_tx(&p_twi_instance, htu21d_address, &trigger_temperature_no_hold_master, 1, true);//Writing 0xE3 to HTU21D tell the sensor to start temperature readings and hold the master
nrf_delay_ms(50);//Delay 50 ms, which is the maximum measurement time stated in datasheet
ret_code = nrf_drv_twi_rx(&p_twi_instance, htu21d_address, returned_over_I2C, 3, false); //Get raw temperature data
nrf_delay_ms(5);
uint16_t x = (returned_over_I2C[0]<<8) | returned_over_I2C[1];
float tempRH = x /(float) 65536; //2^16 = 65536
float rh = -46.85 + (175.72 * tempRH);
*r=rh;
}

I2C interface with HTU21D using nrf51822

Top Replies