mesh dfu timeout

[AndyM]

Hello

I'm exploring the mesh dfu transfer, get some strange results

Here is the setup

1 distributor, 1 target

On the distributor I start  the transfer with mesh models dfd start 0 0 command

In about 40 minutes it completes, and the image is applied but I get a timeout message on the distributor side

However on the target I see a message from the mcuboot that the new message was applied successfully - and actually it is working just fine

Log from the distributor and the target below

Another question

The progress in the JSON below is "50" which I think is because the function that calculates progress divides by 2:

Function cmd_dfd_receivers_get()  in dfd.c  has this lihe

uint8_t progress = bt_mesh_dfu_cli_progress(&dfd_srv->dfu) / 2;

However if I use 

mesh models dfu cli progress command it returns
DFU progress: 100 %

Bug?

Thank you

Andy

--------------------------------

Logs

Distributor

rtt:~$ [00:40:51.061,126] <dbg> bt_mesh_blob_cli: broadcast_complete: continuing
rtt:~$ [00:40:51.061,157] <dbg> bt_mesh_dfu_cli: dfu_complete:
rtt:~$ [00:40:51.061,187] <dbg> bt_mesh_dfd_srv: dfu_ended: reason: 0, phase: 1, apply: 1
rtt:~$ Distribution phase changed to Applying Update
rtt:~$ [00:40:51.061,218] <dbg> bt_mesh_dfu_cli: apply:
rtt:~$ rtt:~$ [00:40:51.061,248] <dbg> bt_mesh_blob_cli: blob_cli_broadcast: 1 targets
rtt:~$ rtt:~$ [00:40:51.271,606] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 6, cur state: 4
rtt:~$ [00:40:51.271,636] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x01a2 receiving transfer
rtt:~$ rtt:~$ [00:41:00.282,928] <dbg> bt_mesh_blob_cli: retry_timeout: 5
rtt:~$ rtt:~$ [00:41:09.441,864] <dbg> bt_mesh_blob_cli: retry_timeout: 4
rtt:~$ rtt:~$ [00:41:18.604,400] <dbg> bt_mesh_blob_cli: retry_timeout: 3
rtt:~$ rtt:~$ [00:41:27.766,143] <dbg> bt_mesh_blob_cli: retry_timeout: 2
rtt:~$ rtt:~$ [00:41:36.924,011] <dbg> bt_mesh_blob_cli: retry_timeout: 1
rtt:~$ [00:41:36.924,041] <dbg> bt_mesh_blob_cli: retry_timeout: Transfer timed out.
rtt:~$ [00:41:36.924,041] <dbg> bt_mesh_blob_cli: drop_remaining_targets:
rtt:~$ [00:41:36.924,072] <wrn> bt_mesh_blob_cli: Dropping 0x01a2: 9
rtt:~$ [00:41:36.924,072] <err> bt_mesh_dfu_cli: Target 0x01a2 failed: 3
rtt:~$ [00:41:36.924,102] <dbg> bt_mesh_blob_cli: broadcast_complete: continuing
rtt:~$ [00:41:36.924,102] <dbg> bt_mesh_dfu_cli: dfu_failed: 3
rtt:~$ [00:41:36.924,133] <dbg> bt_mesh_dfd_srv: dfu_ended: reason: 3, phase: 3, apply: 1
rtt:~$ Distribution phase changed to Failed
rtt:~$ rtt:~$ mesh models dfd receivers-get 0 1
{
"target_cnt": 1,
"targets": {
"0": { "blob_addr": 418, "phase": 6, "status": 3, "blob_status": 9, "progress": 50, "img_idx": 0 }
}
}

-----------------------------------------

Target

*** Booting nRF Connect SDK v3.5.99-ncs1-1 ***
Current image version: 2.1.0+8

~$ Firmware upload started

~$ Firmware upload succeeded
Applying the new firmware
*** Booting nRF Connect SDK v3.5.99-ncs1-1 ***
I: Starting bootloader
I: Primary image: magic=unset, swap_type=0x1, copy_done=0x1, image_ok=0x3
I: Secondary image: magic=good, swap_type=0x2, copy_done=0x3, image_ok=0x3
I: Boot source: none
I: Image index: 0, Swap type: test
I: Starting swap using move algorithm.
I: Bootloader chainload address offset: 0x8000
I: Jumping to the first image slot
*** Booting nRF Connect SDK v3.5.99-ncs1-1 ***
Current image version: 2.1.0+9

[Amanda Hsieh]

Hi, 

Are you using the unmodified samples or your own?

Please check if you call bt_mesh_dfu_srv_applied():

https://github.com/nrfconnect/sdk-nrf/blob/dece2a7f6c36674e2714b8dad7294c911548bb62/samples/bluetooth/mesh/dfu/common/src/dfu_target.c#L268-L278

https://github.com/nrfconnect/sdk-nrf/blob/dece2a7f6c36674e2714b8dad7294c911548bb62/samples/bluetooth/mesh/dfu/target/src/main.c#L132

In the new image, are you changing the node's composition data (like the number of models and elements)? I will check if we can reproduce this. Are you changing any timeouts manually?

"50" is not a bug. The output in the json is formatted in the spec units where transfer progress is calculated in 2 precent step. in other words, the output in json is not a percentage but the spec-defined format

-Amanda H.

[AndyM]

I am using unmodified samples you provided. Yes bt_mesh_dfu_srv_applied is called on the target side.

No composition changes in the image, Just the version number

Tried with and without a custom timeout, no difference. Image is transferred, applied and runs on the target just fine, but on the distributor side there is an error after the "apply" step. See logs above

Also, what is phase 10 ? Saw that several times. It's not defined in the headers. Uninitialized variable?

Another quirk I'd like to resolve is  why it fails to proceed with the batch transfer if one of the target nodes is offline

Thanks for clarifying the "50" progress thing

[AndyM]

Amanda Hsieh said:

Can you provide the full log?

See the first log in the ticket. It is from a distribution to 8 nodes with "apply" option. As soon as the transfer to one of the nodes completed, the image was applied. That caused a timeout and the whole batch stopped.

I tried timeout 10, will try something bigger and let you know

Thank you

[AndyM]

Amanda Hsieh said:

Can you provide the full log?

See the first log in the ticket. It is from a distribution to 8 nodes with "apply" option. As soon as the transfer to one of the nodes completed, the image was applied. That caused a timeout and the whole batch stopped.

I tried timeout 10, will try something bigger and let you know

Here is the  status 10 example.

mesh models dfd receivers-get 0 20
{
"target_cnt": 8,
"targets": {
"0": { "blob_addr": 407, "phase": 2, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 },
"1": { "blob_addr": 406, "phase": 2, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 },
"2": { "blob_addr": 992, "phase": 10, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 },
"3": { "blob_addr": 409, "phase": 2, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 },
"4": { "blob_addr": 418, "phase": 2, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 },
"5": { "blob_addr": 995, "phase": 2, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 },
"6": { "blob_addr": 214, "phase": 2, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 },
"7": { "blob_addr": 419, "phase": 2, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 }
}
}

Thank you

[AndyM]

A new problem

I did a firmware distribution of 1 device and the transfer succeeded, so I know the process works fine

Then I  tried to distribute to 8 devices - see node list above. 992 is offline.
Its phase is listed as 10 which does not exist in phase enumeration. But that's the least of my worries

After I sent  "mesh models dfd start 0 0 0 false 7 120"  command I did

"mesh models dfd receivers-get 0 20" periodically but the 
"progress" field remained at 0 for over 5 minutes at which point I canceled the distribution with 
"mesh models dfd cancel" command

After that all my 8 target nodes fail to boot.

Messages in the target node:

*** Booting nRF Connect SDK v3.5.99-ncs1-1 ***
 Recovering the firmware upload
*** Booting nRF Connect SDK v3.5.99-ncs1-1 ***
I: Starting bootloader
I: Primary image: magic=unset, swap_type=0x1, copy_done=0x3, image_ok=0x3
I: Secondary image: magic=unset, swap_type=0x1, copy_done=0x3, image_ok=0x3
I: Boot source: none
I: Image index: 0, Swap type: none
I: Bootloader chainload address offset: 0x8000
I: Jumping to the first image slot
*** Booting nRF Connect SDK v3.5.99-ncs1-1 ***

messages repeat

In the image recovery handler of the target sample there is  this comment

    /* TODO: Need to recover the effect. */

Why is this handler called after the distribution was cancelled?

How do I fix this ?

I am curious, did you test batch distribution? How many targets?  Did you test with some nodes offline? Did you test with more targets than the default 8?

Makes me nervous to deploy this feature if  a simple cancel bricks all devices. Hope this is something that I am doing wrong and there is a fix

Thanks

 

.

[Amanda Hsieh]

phase 10 is the DFU phase, not the dfd phase and is unknown phase which means that no response was ever received from that node:

- https://github.com/zephyrproject-rtos/zephyr/blob/39917ae5e6423fe74edce399b927ddff38670817/include/zephyr/bluetooth/mesh/dfu.h#L73-L74

- https://github.com/zephyrproject-rtos/zephyr/blob/39917ae5e6423fe74edce399b927ddff38670817/include/zephyr/bluetooth/mesh/dfu_cli.h#L63-L64

Progress 0 is because the node with address 992 didn't respond to the Firmware Update Start message, but by the dfu procedure the distributor must get a response from all nodes before starting sending the blob.

timeout_base 120 means that the actual timeout for each DFU phase is 10 * 1000 * (120 + 2) + 7 * 100 = ~20 minutes.

The distributor will repeat the request CONFIG_BT_MESH_BLOB_CLI_BLOCK_RETRIES times, which is 5 by default. So, it will repeat every 4 minutes. The reason I asked to increase timeout_base is because most likely the timeout was shorter than the time needed for devices to flash the new firmware. They need to adjust the timeout based on their setup.

 

Also, since it is a unicast transfer, every chunk transmission will require confirmation from a node which may delay the transfer even more. I recommend to use multicast transfer for nodes more than 2. For this, they need to subscribe all DFU and blob models to the same address and set `group` field to that address in `mesh models dfd start` command.

 

The comment `/* TODO: Need to recover the effect. */` means that the image effect (`img_effect` variable) which is set in `dfu_meta_check` function is not stored anywhere. This code is called after reboot when DFU model recovers the abandoned DFU transfer and is needed to take a decision at the apply phase (see `dfu_appply` function in the same sample).

 

If target devices start to reboot cyclically I suggest to check if `CONFIG_RESET_ON_FATAL_ERROR` Kconfig option is enabled in `build/target/zephyr/.config` and disable it explicitly in the prj.conf. Then run the devices again.

 

I still would like to see the complete log from the distributor and target nodes. Like the first one from RTT that you attached.

[AndyM]

Regarding the multicast transfer

Amanda Hsieh said:

For this, they need to subscribe all DFU and blob models to the same address and set `group` field to that address in `mesh models dfd start` command.

I assume you are referring to the target nodes?

Amanda Hsieh said:

Progress 0 is because the node with address 992 didn't respond to the Firmware Update Start message, but by the dfu procedure the distributor must get a response from all nodes before starting sending the blob.

This is unfortunate. On a live mesh network with many nodes there will always be a node that would not respond for a variety of reasons. If the whole process is blocked by just one node it makes it not very usable in a real life situation. 

I will provide the logs you requested. May take a while

Thanks a lot for your help

[AndyM]

Here is the log from the distributor right before the image finished transferring

Questions

1. What do the  warnings about "no free slots for segmented messages" mean? Is it something that needs to be addressed? Number of slots increased?

2. Timeout base was set to 10. Still got an error applying on the distributor side. On the target side the image was applied and is running 

Thoughts?

Thank you

rtt:~$ [05:11:41.929,473] <dbg> bt_mesh_blob_cli: blob_cli_broadcast: 8 targets
rtt:~$ rtt:~$ [05:11:42.036,682] <dbg> bt_mesh_blob_cli: handle_block_status: status: 0 block: 98 encoding: 1
rtt:~$ [05:11:42.036,712] <dbg> bt_mesh_blob_cli: rx_block_status: 0x0197: block: 98 status: 0
rtt:~$ [05:11:42.036,712] <dbg> bt_mesh_blob_cli: rx_block_status: Target 0x0197 received all chunks
rtt:~$ [05:11:42.036,743] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0197, pending: 8
rtt:~$ [05:11:42.059,356] <dbg> bt_mesh_blob_cli: handle_block_status: status: 0 block: 98 encoding: 1
rtt:~$ [05:11:42.059,387] <dbg> bt_mesh_blob_cli: rx_block_status: 0x0196: block: 98 status: 0
rtt:~$ [05:11:42.059,387] <dbg> bt_mesh_blob_cli: rx_block_status: Target 0x0196 received all chunks
rtt:~$ [05:11:42.059,417] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0196, pending: 7
rtt:~$ [05:11:42.150,360] <dbg> bt_mesh_blob_cli: handle_block_status: status: 0 block: 98 encoding: 1
rtt:~$ [05:11:42.150,390] <dbg> bt_mesh_blob_cli: rx_block_status: 0x03e5: block: 98 status: 0
rtt:~$ [05:11:42.150,421] <dbg> bt_mesh_blob_cli: rx_block_status: Target 0x03e5 received all chunks
rtt:~$ [05:11:42.150,421] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e5, pending: 6
rtt:~$ [05:11:42.162,811] <dbg> bt_mesh_blob_cli: handle_block_status: status: 0 block: 98 encoding: 1
rtt:~$ rtt:~$ [05:11:42.162,811] <dbg> bt_mesh_blob_cli: rx_block_status: 0x0199: block: 98 status: 0
rtt:~$ [05:11:42.162,841] <dbg> bt_mesh_blob_cli: rx_block_status: Target 0x0199 received all chunks
rtt:~$ [05:11:42.162,841] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0199, pending: 5
rtt:~$ [05:11:42.222,076] <dbg> bt_mesh_blob_cli: handle_block_status: status: 0 block: 98 encoding: 1
rtt:~$ [05:11:42.222,106] <dbg> bt_mesh_blob_cli: rx_block_status: 0x01a2: block: 98 status: 0
rtt:~$ [05:11:42.222,106] <dbg> bt_mesh_blob_cli: rx_block_status: Target 0x01a2 received all chunks
rtt:~$ [05:11:42.222,137] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a2, pending: 4
rtt:~$ [05:11:42.265,563] <dbg> bt_mesh_blob_cli: handle_block_status: status: 0 block: 98 encoding: 1
rtt:~$ [05:11:42.265,594] <dbg> bt_mesh_blob_cli: rx_block_status: 0x03e3: block: 98 status: 0
rtt:~$ [05:11:42.265,594] <dbg> bt_mesh_blob_cli: rx_block_status: Target 0x03e3 received all chunks
rtt:~$ [05:11:42.265,625] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e3, pending: 3
rtt:~$ [05:11:42.356,536] <dbg> bt_mesh_blob_cli: handle_block_status: status: 0 block: 98 encoding: 1
rtt:~$ rtt:~$ [05:11:42.356,567] <dbg> bt_mesh_blob_cli: rx_block_status: 0x00d6: block: 98 status: 0
rtt:~$ [05:11:42.356,597] <dbg> bt_mesh_blob_cli: rx_block_status: Target 0x00d6 received all chunks
rtt:~$ [05:11:42.356,597] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x00d6, pending: 2
rtt:~$ [05:11:42.400,756] <dbg> bt_mesh_blob_cli: handle_block_status: status: 0 block: 98 encoding: 1
rtt:~$ [05:11:42.400,787] <dbg> bt_mesh_blob_cli: rx_block_status: 0x01a0: block: 98 status: 0
rtt:~$ [05:11:42.400,787] <dbg> bt_mesh_blob_cli: rx_block_status: Target 0x01a0 received all chunks
rtt:~$ [05:11:42.400,817] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a0, pending: 1
rtt:~$ [05:11:42.400,848] <dbg> bt_mesh_blob_cli: broadcast_complete: continuing
rtt:~$ [05:11:42.400,848] <dbg> bt_mesh_blob_cli: block_check_end:
rtt:~$ [05:11:42.400,878] <dbg> bt_mesh_blob_cli: block_check_end: No more missing chunks for block 98
rtt:~$ [05:11:42.400,970] <dbg> bt_mesh_blob_cli: confirm_transfer:
rtt:~$ [05:11:42.401,000] <dbg> bt_mesh_blob_cli: blob_cli_broadcast: 8 targets
rtt:~$ rtt:~$ [05:11:42.569,824] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.639,770] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.643,768] <dbg> bt_mesh_blob_cli: handle_xfer_status: status: 0 push phase: 4 f7f9a7fa30859b6a
rtt:~$ [05:11:42.643,798] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0197, pending: 8
rtt:~$ [05:11:42.716,674] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.761,138] <dbg> bt_mesh_blob_cli: handle_xfer_status: status: 0 push phase: 4 f7f9a7fa30859b6a
rtt:~$ [05:11:42.761,138] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0196, pending: 7
rtt:~$ [05:11:42.801,971] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.835,601] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.839,111] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.876,678] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.897,613] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.927,093] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.970,275] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.971,496] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:42.989,379] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ rtt:~$ [05:11:43.002,807] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ rtt:~$ [05:11:43.040,893] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:43.082,519] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:43.103,149] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:43.114,624] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:43.160,095] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ [05:11:43.280,578] <dbg> bt_mesh_blob_cli: handle_xfer_status: status: 0 push phase: 4 f7f9a7fa30859b6a
rtt:~$ [05:11:43.280,609] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e5, pending: 6
rtt:~$ [05:11:43.350,433] <dbg> bt_mesh_blob_cli: handle_xfer_status: status: 0 push phase: 4 f7f9a7fa30859b6a
rtt:~$ [05:11:43.350,433] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0199, pending: 5
rtt:~$ [05:11:43.616,241] <dbg> bt_mesh_blob_cli: handle_xfer_status: status: 0 push phase: 4 f7f9a7fa30859b6a
rtt:~$ [05:11:43.616,271] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a2, pending: 4
rtt:~$ [05:11:43.660,980] <wrn> bt_mesh_transport: No free slots for new incoming segmented messages
rtt:~$ rtt:~$ [05:11:43.712,341] <dbg> bt_mesh_blob_cli: handle_xfer_status: status: 0 push phase: 4 f7f9a7fa30859b6a
rtt:~$ [05:11:43.712,371] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e3, pending: 3
rtt:~$ rtt:~$ [05:11:43.828,063] <dbg> bt_mesh_blob_cli: handle_xfer_status: status: 0 push phase: 4 f7f9a7fa30859b6a
rtt:~$ [05:11:43.828,094] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x00d6, pending: 2
rtt:~$ [05:11:44.346,954] <dbg> bt_mesh_blob_cli: handle_xfer_status: status: 0 push phase: 4 f7f9a7fa30859b6a
rtt:~$ [05:11:44.346,954] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a0, pending: 1
rtt:~$ [05:11:44.346,984] <dbg> bt_mesh_blob_cli: broadcast_complete: continuing
rtt:~$ [05:11:44.347,015] <dbg> bt_mesh_blob_cli: end: 1
rtt:~$ [05:11:44.347,015] <dbg> bt_mesh_dfu_cli: refresh:
rtt:~$ [05:11:44.347,045] <dbg> bt_mesh_blob_cli: blob_cli_broadcast: 8 targets
rtt:~$ [05:11:44.537,017] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 4, cur state: 2
rtt:~$ [05:11:44.537,048] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x0197 receiving transfer
rtt:~$ [05:11:44.537,048] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0197, pending: 8
rtt:~$ [05:11:44.576,599] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 4, cur state: 2
rtt:~$ rtt:~$ [05:11:44.576,629] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x0196 receiving transfer
rtt:~$ [05:11:44.576,629] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0196, pending: 7
rtt:~$ [05:11:44.639,038] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 4, cur state: 2
rtt:~$ [05:11:44.639,038] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x03e5 receiving transfer
rtt:~$ [05:11:44.639,068] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e5, pending: 6
rtt:~$ rtt:~$ [05:11:44.805,175] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 4, cur state: 2
rtt:~$ [05:11:44.805,206] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x0199 receiving transfer
rtt:~$ [05:11:44.805,206] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0199, pending: 5
rtt:~$ [05:11:44.937,713] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 4, cur state: 2
rtt:~$ [05:11:44.937,713] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x01a2 receiving transfer
rtt:~$ [05:11:44.937,744] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a2, pending: 4
rtt:~$ [05:11:45.050,140] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 4, cur state: 2
rtt:~$ [05:11:45.050,140] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x03e3 receiving transfer
rtt:~$ [05:11:45.050,170] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e3, pending: 3
rtt:~$ [05:11:45.217,559] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 4, cur state: 2
rtt:~$ [05:11:45.217,590] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x00d6 receiving transfer
rtt:~$ [05:11:45.217,620] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x00d6, pending: 2
rtt:~$ [05:11:45.292,846] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 4, cur state: 2
rtt:~$ rtt:~$ [05:11:45.292,877] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x01a0 receiving transfer
rtt:~$ [05:11:45.292,877] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a0, pending: 1
rtt:~$ [05:11:45.292,907] <dbg> bt_mesh_blob_cli: broadcast_complete: continuing
rtt:~$ [05:11:45.292,938] <dbg> bt_mesh_dfu_cli: dfu_complete:
rtt:~$ [05:11:45.292,938] <dbg> bt_mesh_dfd_srv: dfu_ended: reason: 0, phase: 1, apply: 0
rtt:~$ Distribution phase changed to Transfer Success

rtt:~$ rtt:~$ mesh models dfd apply
{ "status": 0, "phase": 3, "group": 0, "app_idx": 0, "ttl": 7, "timeout_base": 20, "xfer_mode": 1, "apply": 0, "slot_idx": 0 }
rtt:~$ [05:44:02.960,601] <dbg> bt_mesh_dfu_cli: apply:
rtt:~$ [05:44:02.960,632] <dbg> bt_mesh_blob_cli: blob_cli_broadcast: 8 targets
rtt:~$ Distribution phase changed to Applying Update
rtt:~$ [05:44:03.086,822] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 6, cur state: 4
rtt:~$ [05:44:03.086,822] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x0197 receiving transfer
rtt:~$ [05:44:03.149,230] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 6, cur state: 4
rtt:~$ [05:44:03.149,261] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x0196 receiving transfer
rtt:~$ [05:44:03.241,210] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 6, cur state: 4
rtt:~$ [05:44:03.241,241] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x03e5 receiving transfer
rtt:~$ [05:44:03.322,570] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 6, cur state: 4
rtt:~$ [05:44:03.322,601] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x0199 receiving transfer
rtt:~$ rtt:~$ [05:44:03.558,776] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 6, cur state: 4
rtt:~$ [05:44:03.558,776] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x01a2 receiving transfer
rtt:~$ [05:44:03.630,737] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 6, cur state: 4
rtt:~$ [05:44:03.630,737] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x03e3 receiving transfer
rtt:~$ [05:44:03.715,850] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 6, cur state: 4
rtt:~$ [05:44:03.715,850] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x00d6 receiving transfer
rtt:~$ [05:44:03.818,969] <dbg> bt_mesh_dfu_cli: handle_status: 0 phase: 6, cur state: 4
rtt:~$ [05:44:03.819,000] <dbg> bt_mesh_dfu_cli: handle_status: Target 0x01a0 receiving transfer
rtt:~$ rtt:~$ [05:44:47.864,501] <dbg> bt_mesh_blob_cli: retry_timeout: 5
rtt:~$ [05:44:47.931,579] <dbg> bt_mesh_dfu_cli: handle_status: 2 phase: 0, cur state: 4
rtt:~$ [05:44:47.931,579] <dbg> bt_mesh_dfu_cli: handle_status: Response received with Idle phase
rtt:~$ [05:44:47.931,610] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0197, pending: 8
rtt:~$ [05:44:47.977,020] <dbg> bt_mesh_dfu_cli: handle_status: 2 phase: 0, cur state: 4
rtt:~$ [05:44:47.977,050] <dbg> bt_mesh_dfu_cli: handle_status: Response received with Idle phase
rtt:~$ [05:44:47.977,050] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0196, pending: 7
rtt:~$ [05:44:48.038,604] <dbg> bt_mesh_dfu_cli: handle_status: 2 phase: 0, cur state: 4
rtt:~$ [05:44:48.038,604] <dbg> bt_mesh_dfu_cli: handle_status: Response received with Idle phase
rtt:~$ [05:44:48.038,635] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e5, pending: 6
rtt:~$ [05:44:48.120,971] <dbg> bt_mesh_dfu_cli: handle_status: 2 phase: 0, cur state: 4
rtt:~$ [05:44:48.120,971] <dbg> bt_mesh_dfu_cli: handle_status: Response received with Idle phase
rtt:~$ [05:44:48.121,002] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0199, pending: 5
rtt:~$ rtt:~$ [05:44:48.143,829] <dbg> bt_mesh_dfu_cli: handle_status: 2 phase: 0, cur state: 4
rtt:~$ [05:44:48.143,829] <dbg> bt_mesh_dfu_cli: handle_status: Response received with Idle phase
rtt:~$ [05:44:48.143,859] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a2, pending: 4
rtt:~$ rtt:~$ [05:44:48.211,273] <dbg> bt_mesh_dfu_cli: handle_status: 2 phase: 0, cur state: 4
rtt:~$ [05:44:48.211,303] <dbg> bt_mesh_dfu_cli: handle_status: Response received with Idle phase
rtt:~$ [05:44:48.211,303] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e3, pending: 3
rtt:~$ [05:44:48.278,472] <dbg> bt_mesh_dfu_cli: handle_status: 2 phase: 0, cur state: 4
rtt:~$ [05:44:48.278,503] <dbg> bt_mesh_dfu_cli: handle_status: Response received with Idle phase
rtt:~$ [05:44:48.278,503] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x00d6, pending: 2
rtt:~$ [05:44:48.312,652] <dbg> bt_mesh_dfu_cli: handle_status: 2 phase: 0, cur state: 4
rtt:~$ [05:44:48.312,683] <dbg> bt_mesh_dfu_cli: handle_status: Response received with Idle phase
rtt:~$ [05:44:48.312,683] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a0, pending: 1
rtt:~$ [05:44:48.321,777] <dbg> bt_mesh_blob_cli: broadcast_complete: continuing
rtt:~$ [05:44:48.321,807] <dbg> bt_mesh_dfu_cli: dfu_applied:
rtt:~$ [05:44:48.321,807] <dbg> bt_mesh_dfu_cli: confirm:
rtt:~$ [05:44:48.321,899] <dbg> bt_mesh_blob_cli: blob_cli_broadcast: 8 targets
rtt:~$ rtt:~$ [05:44:48.453,460] <dbg> bt_mesh_dfu_cli: handle_info_status: Image list from 0x0197 from index 0
rtt:~$ [05:44:48.453,521] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000
rtt:~$ [05:44:48.453,582] <wrn> bt_mesh_dfu_cli: Target 0x0197 failed to apply image: 020100000000000a
rtt:~$ [05:44:48.453,582] <err> bt_mesh_dfu_cli: Target 0x0197 failed: 3
rtt:~$ [05:44:48.453,613] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0197, pending: 8
rtt:~$ [05:44:48.502,838] <dbg> bt_mesh_dfu_cli: handle_info_status: Image list from 0x0196 from index 0
rtt:~$ [05:44:48.502,868] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000
rtt:~$ [05:44:48.502,929] <wrn> bt_mesh_dfu_cli: Target 0x0196 failed to apply image: 020100000000000a
rtt:~$ [05:44:48.502,929] <err> bt_mesh_dfu_cli: Target 0x0196 failed: 3
rtt:~$ [05:44:48.502,960] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0196, pending: 7
rtt:~$ [05:44:48.576,080] <dbg> bt_mesh_dfu_cli: handle_info_status: Image list from 0x03e5 from index 0
rtt:~$ rtt:~$ [05:44:48.576,171] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000
rtt:~$ [05:44:48.576,232] <wrn> bt_mesh_dfu_cli: Target 0x03e5 failed to apply image: 020100000000000a
rtt:~$ [05:44:48.576,232] <err> bt_mesh_dfu_cli: Target 0x03e5 failed: 3
rtt:~$ [05:44:48.576,263] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e5, pending: 6
rtt:~$ rtt:~$ [05:44:48.685,485] <dbg> bt_mesh_dfu_cli: handle_info_status: Image list from 0x0199 from index 0
rtt:~$ [05:44:48.685,516] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000
rtt:~$ [05:44:48.685,577] <wrn> bt_mesh_dfu_cli: Target 0x0199 failed to apply image: 020100000000000a
rtt:~$ [05:44:48.685,607] <err> bt_mesh_dfu_cli: Target 0x0199 failed: 3
rtt:~$ [05:44:48.685,607] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x0199, pending: 5
rtt:~$ [05:44:48.860,198] <dbg> bt_mesh_dfu_cli: handle_info_status: Image list from 0x01a2 from index 0
rtt:~$ [05:44:48.860,260] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000
rtt:~$ [05:44:48.860,290] <wrn> bt_mesh_dfu_cli: Target 0x01a2 failed to apply image: 020100000000000a
rtt:~$ [05:44:48.860,321] <err> bt_mesh_dfu_cli: Target 0x01a2 failed: 3
rtt:~$ [05:44:48.860,321] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a2, pending: 4
rtt:~$ rtt:~$ [05:44:48.992,858] <dbg> bt_mesh_dfu_cli: handle_info_status: Image list from 0x03e3 from index 0
rtt:~$ [05:44:48.992,889] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000
rtt:~$ [05:44:48.992,950] <wrn> bt_mesh_dfu_cli: Target 0x03e3 failed to apply image: 020100000000000a
rtt:~$ [05:44:48.992,980] <err> bt_mesh_dfu_cli: Target 0x03e3 failed: 3
rtt:~$ [05:44:48.992,980] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x03e3, pending: 3
rtt:~$ [05:44:49.118,438] <dbg> bt_mesh_dfu_cli: handle_info_status: Image list from 0x00d6 from index 0
rtt:~$ [05:44:49.118,499] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000
rtt:~$ [05:44:49.118,560] <wrn> bt_mesh_dfu_cli: Target 0x00d6 failed to apply image: 020100000000000a
rtt:~$ [05:44:49.118,560] <err> bt_mesh_dfu_cli: Target 0x00d6 failed: 3
rtt:~$ [05:44:49.118,591] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x00d6, pending: 2
rtt:~$ rtt:~$ [05:44:49.213,592] <dbg> bt_mesh_dfu_cli: handle_info_status: Image list from 0x01a0 from index 0
rtt:~$ [05:44:49.213,653] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000
rtt:~$ [05:44:49.213,714] <wrn> bt_mesh_dfu_cli: Target 0x01a0 failed to apply image: 020100000000000a
rtt:~$ [05:44:49.213,714] <err> bt_mesh_dfu_cli: Target 0x01a0 failed: 3
rtt:~$ [05:44:49.213,745] <dbg> bt_mesh_blob_cli: blob_cli_broadcast_rsp: 0x01a0, pending: 1
rtt:~$ [05:44:49.213,775] <dbg> bt_mesh_blob_cli: broadcast_complete: continuing
rtt:~$ [05:44:49.213,775] <dbg> bt_mesh_dfu_cli: dfu_failed: 3
rtt:~$ [05:44:49.213,806] <dbg> bt_mesh_dfd_srv: dfu_ended: reason: 3, phase: 3, apply: 0
rtt:~$ Distribution phase changed to Failed

[Amanda Hsieh]

Hi,

AndyM said:

rtt:~$ [05:44:48.453,521] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000

You should increase the value of CONFIG_BT_MESH_SEG_BUFS to 80 or 100. 

AndyM said:

2. Timeout base was set to 10. Still got an error applying on the distributor side. On the target side the image was applied and is running 

Thoughts?

All targets replied with fwid 020100000a000000:

rtt:~$ [05:44:48.685,516] <dbg> bt_mesh_dfu_cli: handle_info_status: Image 0
fwid: 020100000a000000

But fwid on the distributor is 020100000000000a:

rtt:~$ [05:44:48.685,577] <wrn> bt_mesh_dfu_cli: Target 0x0199 failed to apply image: 020100000000000a

This value should be used when adding a new slot on the distributor. Please check what fwid you set through mesh models dfu slot add. It should be equal to mcuboot image version encoded into struct mcuboot_img_sem_ver:

• See Firmware ID section: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/mesh/dfu/target/README.html#performing-a-device-firmware-update 
• https://github.com/nrfconnect/sdk-nrf/blob/11645184a54d02921bb0691a57e1e86c141393da/samples/bluetooth/mesh/dfu/common/src/dfu_target.c#L25-L28 
• https://github.com/nrfconnect/sdk-nrf/blob/11645184a54d02921bb0691a57e1e86c141393da/samples/bluetooth/mesh/dfu/common/src/dfu_target.c#L242-L256

-Amanda H.

[AndyM]

Great, thank you. I'll implement your suggestions and let you know

Really appreciate your help

[AndyM]

The failure to apply on the distributor side was due to the wrong firmware ID provided to "slot add" command. Once that was corrected the apply completed successfully on the distributor side

Tried using group address to transfer  - results are unexpected.

It took 2 hours and 40 minutes to transfer to 1 device. Without using a  group address it takes 40 minutes

I will try with multiple devices and let you know.

Without group address it took about 5 hours to transfer to 8 devices

[AndyM]

Tried 8 devices

On the target side subscribed 

BT_MESH_MODEL_ID_BLOB_SRV (0x1400) and 

BT_MESH_MODEL_ID_DFU_SRV  (0x1402)  to the group address 0xC008 

Then I used the command

mesh models dfd start 0 0 0xC008 false 7 20

I get the following

mesh models dfd start 0 0 0xC008 false 7 20
{ "status": 0, "phase": 1, "group": 49160, "app_idx": 0, "ttl": 7, "timeout_base": 20, "xfer_mode": 1, "apply": 0, "slot_idx": 0 }
mdist:~$ Starting the firmware distribution.
Slot:
Size: 403239 bytes
FWID: 020100000c000000
Metadata:
[00:02:10.500,823] <dbg> bt_mesh_dfd_srv: bt_mesh_dfd_srv_start: Distribution Start: slot: 0, appidx: 0, tb: 20, addr: C008, ttl: 7, apply: 0
Distribution phase changed to Transfer Active
[00:02:10.500,976] <dbg> bt_mesh_dfu_cli: initiate:
[00:02:10.501,007] <dbg> bt_mesh_blob_cli: blob_cli_broadcast: 3 targets
[00:02:10.667,205] <wrn> bt_mesh_transport: Replay: src 0x0199 dst 0x0356 seq 0x000102
[00:02:10.749,511] <wrn> bt_mesh_transport: Replay: src 0x0196 dst 0x0356 seq 0x000083
[00:02:10.750,885] <wrn> bt_mesh_transport: Replay: src 0x0199 dst 0x0356 seq 0x000103
[00:02:10.787,658] <wrn> bt_mesh_transport: Replay: src 0x0197 dst 0x0356 seq 0x000226
[00:02:10.810,913] <wrn> bt_mesh_transport: Replay: src 0x01a2 dst 0x0356 seq 0x000082
[00:02:10.855,224] <wrn> bt_mesh_transport: Replay: src 0x01a0 dst 0x0356 seq 0x0002ac
[00:02:10.862,030] <wrn> bt_mesh_transport: Replay: src 0x0197 dst 0x0356 seq 0x000227
[00:02:10.890,319] <wrn> bt_mesh_transport: Replay: src 0x01a2 dst 0x0356 seq 0x000083
[00:02:10.913,360] <wrn> bt_mesh_transport: Replay: src 0x01a0 dst 0x0356 seq 0x0002ad
[00:02:10.938,659] <wrn> bt_mesh_transport: Replay: src 0x03e3 dst 0x0356 seq 0x000082
[00:02:10.954,711] <wrn> bt_mesh_transport: Replay: src 0x03e3 dst 0x0356 seq 0x000083
[00:02:11.038,574] <wrn> bt_mesh_transport: Replay: src 0x00d6 dst 0x0356 seq 0x000082
[00:02:11.095,733] <wrn> bt_mesh_transport: Replay: src 0x00d6 dst 0x0356 seq 0x000083
[00:02:11.128,143] <wrn> bt_mesh_transport: Replay: src 0x03e5 dst 0x0356 seq 0x0001a0
[00:02:11.205,993] <wrn> bt_mesh_transport: Replay: src 0x03e5 dst 0x0356 seq 0x0001a1
[

mdist:~$ mesh models dfd receivers-get 0 20
{
"target_cnt": 3,
"targets": {
"0": { "blob_addr": 406, "phase": 10, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 },
"1": { "blob_addr": 409, "phase": 10, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 },
"2": { "blob_addr": 995, "phase": 10, "status": 0, "blob_status": 0, "progress": 0, "img_idx": 0 }
}
}
replay warnings continue until eventually I get

[00:05:55.908,813] <dbg> bt_mesh_blob_cli: retry_timeout: Transfer timed out.
[00:05:55.908,813] <dbg> bt_mesh_blob_cli: drop_remaining_targets:
[00:05:55.908,843] <wrn> bt_mesh_blob_cli: Dropping 0x0196: 9
[00:05:55.908,843] <err> bt_mesh_dfu_cli: Target 0x0196 failed: 3
[00:05:55.908,843] <wrn> bt_mesh_blob_cli: Dropping 0x0199: 9
[00:05:55.908,874] <err> bt_mesh_dfu_cli: Target 0x0199 failed: 3
[00:05:55.908,874] <wrn> bt_mesh_blob_cli: Dropping 0x03e3: 9
[00:05:55.908,874] <err> bt_mesh_dfu_cli: Target 0x03e3 failed: 3
[00:05:55.908,905] <dbg> bt_mesh_blob_cli: broadcast_complete: continuing
[00:05:55.908,935] <dbg> bt_mesh_dfu_cli: transfer:
[00:05:55.908,966] <dbg> bt_mesh_dfu_cli: dfu_failed: 3
[00:05:55.908,966] <dbg> bt_mesh_dfd_srv: dfu_ended: reason: 3, phase: 1, apply: 0
Distribution phase changed to Failed

Another quirk

I have 8 devices. Only added 3 addresses to the distributor list, yet get the  dfd_start() callback called on ALL 8 devices. Why?d
What else do I need to do to make it work?

Thanks