how to erase UICR on nrf52832 from the code (not from nrfjprog)

[BrianW]

I want to update some data stored in UICR CUSTOMER area on an nrf52832.

Code to do this works fine, as long as the areas are already erased (0xFFFFFFFF).

However, if they have already had a value written, and I want to update it, I understand I need to erase the UICR area first as its flash.

My process is

- copy out the non-CUSTOMER registers, to save them

- enable erase in the NVMC CONFIG

- ask the NVMC to erase by writing 1 to ERASEUICR register

- enable writing

- write back the saved registers

- go back to read mode

(and then do my usual writing code)

However, as soon as I start the process the MCU hangs (no logs, no crash, just hung).

Here is my code : I never see any of the logs probably coz the UART doesn't manage to get the bytes out!

static void _erase_uicr() {
    // Preserve nordic registers. Note RESERVED fields can be ignored
    uint32_t nrffw[15];
    uint32_t nrfhw[12];
    uint32_t pselreset0;
    uint32_t pselreset1;
    uint32_t approtect;
    uint32_t nfcpins;
    log_info("ERASE UICR");

    for (int i=0;i<15;i++) {
        nrffw[i] = NRF_UICR->NRFFW[i];
    }
    for (int i=0;i<12;i++) {
        nrfhw[i] = NRF_UICR->NRFHW[i];
    }
    approtect = NRF_UICR->APPROTECT;
    pselreset0 = NRF_UICR->PSELRESET[0];
    pselreset1 = NRF_UICR->PSELRESET[1];
    nfcpins = NRF_UICR->NFCPINS;
    log_info("SAVED UICR info");
    // Enable erasing
    NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Een;      // erase enabled
    while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
    log_info("ENABLED ERASE UICR");
    // Must erase UICR first
    NRF_NVMC->ERASEUICR = 0x00000001;
    while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
    log_info("ERASED UICR");
    NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen;      // write enabled
    while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
    log_info("ENABLED WRITE UICR");
    // Write back the copies
    for (int i=0;i<15;i++) {
        NRF_UICR->NRFFW[i] = nrffw[i];
    }
    for (int i=0;i<12;i++) {
        NRF_UICR->NRFHW[i] = nrfhw[i];
    }
    NRF_UICR->APPROTECT = approtect;
    NRF_UICR->PSELRESET[0] = pselreset0;
    NRF_UICR->PSELRESET[1] = pselreset1;
    NRF_UICR->NFCPINS = nfcpins;

    log_info("REWROTE NON-CUSTOMER UICR");

    NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren;      // RO
    while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
    log_info("BACK TO RO UICR");

}

Any ideas what I'm doing wrong?

Thanks

[Susheel Nuguru]

You are enabling approtect, enabling read mode and then writing the rest of the registers?  Why write after enabling read mode? 

I suggest you to start debugger and let this code run and then pause the debugger to see where it is "hung", to understand the context. I am guessing it is looping in fault handler.

[BrianW]

Susheel Nuguru said:

You are enabling approtect, enabling read mode and then writing the rest of the registers?  Why write after enabling read mode? 

No, I read out the registers in UICR that will be lost when I do ERASEUICR, then set them back to the saved values afterwards. I just want to preserve them over ERASEUICR!

[BrianW]

Came back to retry to fix this with the debugger, but the problem has gone...it now correctly manages to erase the UICR customer registers, while (as far as I can see) preserving the others.

Maybe an interaction with the SoftDevice bluetooth stack running while my code was running...

[BrianW]

I can confirm the issue is with the SoftDevice ble stack : as this takes offense and reboots if it can't schedule as it needs, this can happen during the UICR erase (as the code has to wait for this to finish), and so can get randomly rebooted....

My workaround is to only update the UICR ina mode without SD running....

[Susheel Nuguru]

You cannot touch UICR registers directly when using the softdevice that is when softdevice is enabled. You need to use softdevice enabled functions like 

sd_flash_page_erase

sd_flash_write 

UICR is a protected peripheral when softdevice is enabled.

[BrianW]

Susheel Nuguru said:

UICR is a protected peripheral when softdevice is enabled.

Does this mean there is no way to write to UICR when softdevice is enabled? (no sd_uicr_write or similar?)

In a related topic, does doing the Nordic DFU operation delete or modify the UICR? (specifically the CUSTOMER[] words) 

[Susheel Nuguru]

Yes, disable the softdevice temporarily and write to the UICR register and then enable the softdevice later.

[BrianW]

Ok, thanks!