I am trying to make a remote control with NRF24 and Atmega328p. The full name of the NRF24 I am using is E01-ML01SP2. I fixed everything but it draws too much current. I have a remote control made by someone else and it draws 10 mAh but mine draws 70mAh. I am using Arduino IDE as a studio. I want to share my transmitter software with you.
#include "PinChangeInterrupt.h"
#include <avr/sleep.h>
#include <avr/interrupt.h>
#include <SPI.h>
#include <nRF24L01.h>
#include <RF24.h>
RF24 kablosuz(9, 10);
const byte adres[] = "arkis";
#define BTN0_PIN 5
#define BTN1_PIN 3
#define BTN2_PIN 4
#define BTN3_PIN 2
#define LED0_PIN 7
int led_yak1[1];
int led_yak2[1];
int led_yak3[1];
int led_yak4[1];
int led_sondur[1];
//PİL DEĞER OKUMA
const int ledPin = 6;
const int sensorPin = A0;
int sensorValue = 0;
const int threshold = 530; //1.71V
void BTN0_ISR(void)
{
wakeUp();
sensorValue = analogRead(sensorPin);
if (sensorValue > threshold) {
while (digitalRead(BTN0_PIN) == HIGH)
{
kablosuz.write(led_yak1, 1);
digitalWrite(LED0_PIN,HIGH);
}
kablosuz.write(led_sondur, 1);
digitalWrite(LED0_PIN,LOW);
}
else{
digitalWrite(ledPin,HIGH);
delay(500);
digitalWrite(ledPin,LOW);
}
}
void BTN1_ISR(void)
{
wakeUp();
sensorValue = analogRead(sensorPin);
if (sensorValue > threshold) {
while (digitalRead(BTN1_PIN) == HIGH)
{
kablosuz.write(led_yak2, 1);
digitalWrite(LED0_PIN,HIGH);
}
kablosuz.write(led_sondur, 1);
digitalWrite(LED0_PIN,LOW);
}
else{
digitalWrite(ledPin,HIGH);
delay(500);
digitalWrite(ledPin,LOW);
}
}
void BTN2_ISR(void)
{
wakeUp();
sensorValue = analogRead(sensorPin);
if (sensorValue > threshold) {
while (digitalRead(BTN2_PIN) == HIGH)
{
kablosuz.write(led_yak3, 1);
digitalWrite(LED0_PIN,HIGH);
}
kablosuz.write(led_sondur, 1);
digitalWrite(LED0_PIN,LOW);
}
else{
digitalWrite(ledPin,HIGH);
delay(500);
digitalWrite(ledPin,LOW);
}
}
void BTN3_ISR(void)
{
wakeUp();
sensorValue = analogRead(sensorPin);
if (sensorValue > threshold) {
while (digitalRead(BTN3_PIN) == HIGH)
{
kablosuz.write(led_yak4, 1);
digitalWrite(LED0_PIN,HIGH);
}
kablosuz.write(led_sondur, 1);
digitalWrite(LED0_PIN,LOW);
}
else{
digitalWrite(ledPin,HIGH);
delay(500);
digitalWrite(ledPin,LOW);
}
}
void wakeUp() {
// Bu fonksiyon boş olabilir, sadece uyandırma için kullanılıyor
}
void setup()
{
kablosuz.begin();
kablosuz.openWritingPipe(adres);
led_yak1[0] = 100;
led_yak2[0] = 125;
led_yak3[0] = 150;
led_yak4[0] = 175;
led_sondur[0] = 0;
pinMode(LED0_PIN, OUTPUT);
pinMode(BTN0_PIN, INPUT);
pinMode(BTN1_PIN, INPUT);
pinMode(BTN2_PIN, INPUT);
pinMode(BTN3_PIN, INPUT);
attachPCINT(digitalPinToPCINT(BTN0_PIN), BTN0_ISR, RISING);
attachPCINT(digitalPinToPCINT(BTN1_PIN), BTN1_ISR, RISING);
attachPCINT(digitalPinToPCINT(BTN2_PIN), BTN2_ISR, RISING);
attachPCINT(digitalPinToPCINT(BTN3_PIN), BTN3_ISR, RISING);
pinMode(ledPin, OUTPUT);
pinMode(sensorPin, INPUT);
}
void loop()
{
set_sleep_mode(SLEEP_MODE_PWR_DOWN);
sleep_enable();
sleep_mode();
sleep_disable();
// Tekrar uyutma hazırlığı
attachInterrupt(digitalPinToInterrupt(BTN0_PIN), wakeUp, RISING);
attachInterrupt(digitalPinToInterrupt(BTN1_PIN), wakeUp, RISING);
attachInterrupt(digitalPinToInterrupt(BTN2_PIN), wakeUp, RISING);
attachInterrupt(digitalPinToInterrupt(BTN3_PIN), wakeUp, RISING);
}
