Hi all,
I'm trying to build an v2.7.0 SLM configured to using UART2 for external MCU on nRF-9151.
But the output image was acting weird...
The 2 virtual COM port of DK board was COM6 and COM7 on my PC, and UART2(PO.28 as input PO.29 as output) was COM1.
While POR of the 9151DK, I will receive the banner message on both COM6 and COM1, but the "Ready\r\n" only would pop up if COM6 was connected by terminal.
That is said if I only monitor COM1 or COM6, I could only receive banner message, SLM wouldn't work.
Only if I am connecting both COM1 and COM6, will the "Ready\r\n" pop up. Also only sending AT commands from COM1 will receive response. (Will response on both COM1 and COM6)
I've followed the page of SLM and modified nrf9151dk_nrf9151_ns.conf and nrf9151dk_nrf9151_ns.overlay. (Copy pasted below)
.conf was modified as suggested on SLM page, while .overlay was also modified as suggested but additionally modified the UART2 NRF_PSEL(TX -> 28, RX->29, RTS->16, CTS->17, according to hardware drawing on the back of DK board).
What am I missing?
--------.conf--------
## Copyright (c) 2024 Nordic Semiconductor ASA## SPDX-License-Identifier: LicenseRef-Nordic-5-Clause## Configuration file for nRF9151DK.# This file is merged with prj.conf in the application folder, and options# set here will take precedence if they are present in both files.# Use UART_0 (when working with PC terminal)# unmask the following config#CONFIG_UART_0_NRF_HW_ASYNC_TIMER=2#CONFIG_UART_0_NRF_HW_ASYNC=y#CONFIG_SLM_POWER_PIN=8#CONFIG_SLM_INDICATE_PIN=0# Use UART_2 (when working with external MCU)# unmask the following configCONFIG_UART_2_NRF_HW_ASYNC_TIMER=2CONFIG_UART_2_NRF_HW_ASYNC=yCONFIG_SLM_POWER_PIN=31CONFIG_SLM_INDICATE_PIN=30/* * Copyright (c) 2024 Nordic Semiconductor ASA * * SPDX-License-Identifier: LicenseRef-Nordic-5-Clause *// { chosen { ncs,slm-uart = &uart2; };};&uart0 { status = "disabled"; hw-flow-control;};&uart2 { compatible = "nordic,nrf-uarte"; current-speed = <115200>; status = "okay"; hw-flow-control; pinctrl-0 = <&uart2_default_alt>; pinctrl-1 = <&uart2_sleep_alt>; pinctrl-names = "default", "sleep";};&i2c2 { status = "disabled";};&pinctrl { uart2_default_alt: uart2_default_alt { group1 { psels = <NRF_PSEL(UART_RX, 0, 28)>; bias-pull-up; }; group2 { psels = <NRF_PSEL(UART_TX, 0, 29)>, <NRF_PSEL(UART_RTS, 0, 16)>, <NRF_PSEL(UART_CTS, 0, 17)>; }; }; uart2_sleep_alt: uart2_sleep_alt { group1 { psels = <NRF_PSEL(UART_TX, 0, 29)>, <NRF_PSEL(UART_RX, 0, 28)>, <NRF_PSEL(UART_RTS, 0, 16)>, <NRF_PSEL(UART_CTS, 0, 17)>; low-power-enable; }; };};