• State Not Answered
  • Replies 7 replies
  • Subscribers 72 subscribers
  • Views 158 views
  • Users 0 members are here
Attachments (0)
Nordic Case Info
  • Case ID: 341039
Options

Cis mode - Mic issues

Abdulmohaimen

Hi,

With this setup in Issue with Stereo Sound from External Codec on nRF5340 DK (SDK v2.6.2) , I successfully built a CIS mode using my nRF5340 DKs, enabling stereo sound while the microphone is active.

However, I am currently experiencing several issues:

  • The recorded microphone signal is accelerated, playing back faster than it was recorded.
  • The input signal quality is poor when using an analog microphone, but it improves significantly with a digital microphone.
  • When using the microphone and playing audio through the headset simultaneously, the recorded sound is barely audible (very low signal strength).
  • Occasionally, one of the DKs disconnects, causing a complete loss of audio.

Any insights into what might be causing these issues? and how might they be solved?

Thank you in advance—I truly appreciate your time and support.

Best regards,
Abdulmohaimen Algamoudi 

  • 0

    Hi,

    On which specific board do you experience issues?

    Do you still use NCS v2.6.2?

    Best regards,
    Dejan

  • 0 in reply to dejans

    Hey Dejan,
    The nrf5340 audio DK as well as the BC40C from Fanstel.
    The sdk is V2.8.0

    Thank you in advance

    Best regards,
    Abdulmohaimen Algamoudi 

  • 0 in reply to Abdulmohaimen

    Hi,

    In your previous ticket you mentioned using USB. Is this still the case?

    Are you switching between analog and digital microphone? If yes, how?

    Could you specify all code changes that you made to the audio application?

    Can you provide serial port log?

    Best regards,
    Dejan


  • 0 in reply to dejans

    Hi Dejan,

    Sorry for the late response—I was on vacation over the past few weeks.

    Yes, I am still using USB.

    I am switching between the analog and digital microphone using an external HW codec (DA7212 evaluation board). I have applied the modifications from the GitHub link and made changes to the hardware codec file to configure the codec. Additionally, I enabled the I2S configuration to utilize the external HW codec.

    I will attach the log files to this ticket.

    I want to mention that with the current configuration, the audio streaming does not remain stable for long (when 2 nrf5340 audio dk as headset r and L at the same time used). After a couple of minutes, the right channel (mostly) disconnects from streaming. Before that, I notice audio cutting out intermittently. (when i use just one it works prefactly  in this regard))

    I would like to emphasize that the main goal is to establish a CIS connection with two microphones (left and right) operating simultaneously. Currently, when using the accelerated microphone signal while the headset is streaming sound, the microphone volume is too low. (Current setup i have CIS mode with some limitions -  accelerated microphone signal  and Channel disconncating as well as the LOW mic when the sound on headphones)

    Additionally, I have another question: If I want to use CONFIG_AUDIO_SOURCE_I2S=y, can I connect it directly via the LINE plug on the nRF5340 Audio DK, or do I need to use an external HW codec? may it solve those problems?

    Looking forward to your feedback. 

    Thank you in advance—I truly appreciate your time and support.

    Best regards 
    Abdulmohaimen 

    *** Booting nRF Connect SDK v2.8.0-a2386bfc8401 ***
*** Using Zephyr OS v3.7.99-0bc3393fb112 ***
HL [00:00:00.279,052] <inf> board_version: Compatible board/HW version found: 1.0.0
HL [00:00:00.311,431] <inf> fw_info: 
         nRF5340 Audio nRF5340 Audio DK cpuapp                      
         NCS base version: 2.8.0                            
         Cmake run : Fri Jan 03 19:31:25 2025
HL [00:00:00.311,431] <inf> fw_info: ------- DEBUG BUILD -------
HL [00:00:00.311,431] <inf> fw_info: HEADSET left device
HL [00:00:00.381,134] <inf> bt_keys: SC LTK: 0xa752d2df8dcdae6a3827ee0019f6d8e1
HL [00:00:00.383,209] <inf> bt_mgmt_ctlr_cfg: Controller: SoftDevice: Version 6.0 (0x0e), Revision 8270
HL [00:00:00.383,422] <inf> bt_mgmt: Local identity addr: F5:FD:57:29:5F:67 (random)
HL [00:00:00.389,129] <inf> bt_mgmt_adv: Local addr: 4B:76:FD:D8:DB:30 (random)
HL [00:00:00.389,190] <inf> bt_mgmt_adv: Adv directed to: D3:C8:9D:D1:BE:66 (random).
HL [00:00:00.389,801] <inf> bt_mgmt_adv: Advertising successfully started
HL [00:00:01.667,388] <inf> bt_mgmt: Connected: D3:C8:9D:D1:BE:66 (random)
HL [00:00:01.667,419] <inf> main: Connection event. Num connections: 1
HL [00:00:01.667,572] <inf> bt_mgmt_adv: RPA (Resolvable Private Address) expired.
HL [00:00:01.667,663] <inf> bt_mgmt_adv: Local addr: 4B:76:FD:D8:DB:30 (random)
HL [00:00:01.748,382] <inf> main: Security changed
HL [00:00:01.748,565] <wrn> bt_gatt: Device is not subscribed to characteristic
HL [00:00:01.748,596] <wrn> bt_pacs: PACS notify failed: -22
HL [00:00:01.748,626] <wrn> bt_gatt: Device is not subscribed to characteristic
HL [00:00:01.748,626] <wrn> bt_pacs: PACS notify failed: -22
HL [00:00:02.318,267] <inf> bt_content_ctrl_media: Discovery of MCS finished
HL [00:00:03.429,138] <inf> le_audio: LC3 codec config for sink:
HL [00:00:03.429,168] <inf> le_audio:   Frequency: 24000 Hz
HL [00:00:03.429,168] <inf> le_audio:   Duration: 10000 us
HL [00:00:03.429,168] <inf> le_audio:   Channel allocation: 0x3
HL [00:00:03.429,168] <inf> le_audio:   Octets per frame: 60 (48000 bps)
HL [00:00:03.429,168] <inf> le_audio:   Frames per SDU: 1
HL [00:00:03.469,146] <inf> le_audio: LC3 codec config for source:
HL [00:00:03.469,146] <inf> le_audio:   Frequency: 24000 Hz
HL [00:00:03.469,146] <inf> le_audio:   Duration: 10000 us
HL [00:00:03.469,177] <inf> le_audio:   Channel allocation: 0x1
HL [00:00:03.469,177] <inf> le_audio:   Octets per frame: 60 (48000 bps)
HL [00:00:03.469,177] <inf> le_audio:   Frames per SDU: 1
HL [00:00:03.549,713] <inf> main: Presentation delay 5000 us is set by initiator
HL [00:00:03.549,743] <inf> main: Presentation delay 5000 us is set by initiator
HL [00:00:04.454,864] <inf> unicast_server: Stream 0x200105f4 started
HL [00:00:04.456,512] <wrn> le_audio_rx: Not in streaming state (1), thrown 1 packet(s)
DAC L gain 112   
ADC L gain 112   
DAC R gain 112   
ADC R gain 112   
HL [00:00:04.486,633] <wrn> audio_datapath: I2S RX overrun. Single msg
HL [00:00:04.490,600] <wrn> audio_datapath: Data received, total under-runs: 11
HL [00:00:04.565,643] <inf> audio_datapath: Drft comp state: CALIB
HL [00:00:04.628,631] <inf> unicast_server: Stream 0x2001061c started
HL [00:00:04.629,638] <wrn> audio_datapath: I2S RX continuing stream
HL [00:00:04.665,649] <inf> audio_datapath: Drft comp state: OFFSET
HL [00:00:05.166,015] <inf> audio_datapath: Drft comp state: LOCKED
HL [00:00:05.174,957] <inf> audio_datapath: Pres comp state: MEAS
HL [00:00:05.284,759] <inf> audio_datapath: Pres comp state: LOCKED
HL [00:00:05.714,996] <wrn> audio_datapath: Data received, total under-runs: 15


    *** Using Zephyr OS v3.7.99-0bc3393fb112 ***
GW [00:00:00.268,615] <inf> board_version: Compatible board/HW version found: 1.0.0
GW [00:00:00.301,055] <inf> fw_info: 
         nRF5340 Audio nRF5340 Audio DK cpuapp                      
         NCS base version: 2.8.0                            
         Cmake run : Thu Jan 02 22:56:22 2025
GW [00:00:00.301,055] <inf> fw_info: ------- DEBUG BUILD -------
GW [00:00:00.301,055] <inf> fw_info: Compiled for GATEWAY device
GW [00:00:00.370,391] <inf> bt_keys: SC LTK: 0xb589a7752caaa3535c4ca66003e0dbde
GW [00:00:00.370,422] <inf> bt_keys: SC LTK: 0xa752d2df8dcdae6a3827ee0019f6d8e1
GW [00:00:00.374,267] <inf> bt_mgmt_ctlr_cfg: Controller: SoftDevice: Version 6.0 (0x0e), Revision 8270
GW [00:00:00.374,450] <inf> bt_mgmt: Local identity addr: D3:C8:9D:D1:BE:66 (random)
GW [00:00:00.374,603] <inf> audio_usb: Ready for USB host to send/receive.
GW [00:00:00.375,732] <inf> bt_mgmt_scan: All bonded slots filled, will not accept new devices
GW [00:00:00.378,112] <inf> bt_mgmt_scan: Local addr: 77:BB:07:16:AE:49 (random). May time out. Updates not printed
GW [00:00:00.378,112] <inf> bt_mgmt_scan: Scanning successfully started
GW [00:00:00.382,476] <inf> bt_mgmt_scan: Creating connection to bonded device: F5:FD:57:29:5F:67 (random)
GW [00:00:00.387,878] <inf> bt_mgmt: Connected: F5:FD:57:29:5F:67 (random)
GW [00:00:00.387,908] <inf> main: Connection event. Num connections: 1
GW [00:00:00.437,774] <wrn> bt_conn: conn 0x20004f08 failed to establish. RF noise?
GW [00:00:00.437,896] <wrn> bt_mgmt: Security failed: level 1 err 9 
GW [00:00:00.437,896] <wrn> bt_mgmt: Failed to disconnect -128
GW [00:00:00.437,957] <wrn> bt_gatt: conn 0x20004f08 err 0x0e
GW [00:00:00.438,171] <inf> bt_mgmt: Disconnected: F5:FD:57:29:5F:67 (random), reason 0x3e 
GW [00:00:00.438,201] <inf> main: Disconnection event. Num connections: 0
GW [00:00:00.438,201] <wrn> unicast_client: Unknown connection disconnected
GW [00:00:00.438,323] <inf> bt_mgmt_scan: All bonded slots filled, will not accept new devices
GW [00:00:00.439,270] <inf> bt_mgmt_scan: Local addr: 77:BB:07:16:AE:49 (random). May time out. Updates not printed
GW [00:00:00.439,270] <inf> bt_mgmt_scan: Scanning successfully started
GW [00:00:00.442,657] <inf> bt_mgmt_scan: Creating connection to bonded device: F5:FD:57:29:5F:67 (random)
GW [00:00:00.448,913] <inf> bt_mgmt: Connected: F5:FD:57:29:5F:67 (random)
GW [00:00:00.448,944] <inf> main: Connection event. Num connections: 1
GW [00:00:00.498,809] <wrn> bt_conn: conn 0x20004f08 failed to establish. RF noise?
GW [00:00:00.498,931] <wrn> bt_mgmt: Security failed: level 1 err 9 
GW [00:00:00.498,962] <wrn> bt_mgmt: Failed to disconnect -128
GW [00:00:00.498,992] <wrn> bt_gatt: conn 0x20004f08 err 0x0e
GW [00:00:00.499,206] <inf> bt_mgmt: Disconnected: F5:FD:57:29:5F:67 (random), reason 0x3e 
GW [00:00:00.499,237] <inf> main: Disconnection event. Num connections: 0
GW [00:00:00.499,237] <wrn> unicast_client: Unknown connection disconnected
GW [00:00:00.499,389] <inf> bt_mgmt_scan: All bonded slots filled, will not accept new devices
GW [00:00:00.500,335] <inf> bt_mgmt_scan: Local addr: 77:BB:07:16:AE:49 (random). May time out. Updates not printed
GW [00:00:00.500,335] <inf> bt_mgmt_scan: Scanning successfully started
GW [00:00:00.504,821] <inf> bt_mgmt_scan: Creating connection to bonded device: F5:FD:57:29:5F:67 (random)
GW [00:00:00.510,192] <inf> bt_mgmt: Connected: F5:FD:57:29:5F:67 (random)
GW [00:00:00.510,223] <inf> main: Connection event. Num connections: 1
GW [00:00:00.560,089] <wrn> bt_conn: conn 0x20004f08 failed to establish. RF noise?
GW [00:00:00.560,211] <wrn> bt_mgmt: Security failed: level 1 err 9 
GW [00:00:00.560,211] <wrn> bt_mgmt: Failed to disconnect -128
GW [00:00:00.560,272] <wrn> bt_gatt: conn 0x20004f08 err 0x0e
GW [00:00:00.560,485] <inf> bt_mgmt: Disconnected: F5:FD:57:29:5F:67 (random), reason 0x3e 
GW [00:00:00.560,516] <inf> main: Disconnection event. Num connections: 0
GW [00:00:00.560,516] <wrn> unicast_client: Unknown connection disconnected
GW [00:00:00.560,638] <inf> bt_mgmt_scan: All bonded slots filled, will not accept new devices
GW [00:00:00.561,584] <inf> bt_mgmt_scan: Local addr: 77:BB:07:16:AE:49 (random). May time out. Updates not printed
GW [00:00:00.561,584] <inf> bt_mgmt_scan: Scanning successfully started
GW [00:00:00.565,185] <inf> bt_mgmt_scan: Creating connection to bonded device: F5:FD:57:29:5F:67 (random)
GW [00:00:00.571,441] <inf> bt_mgmt: Connected: F5:FD:57:29:5F:67 (random)
GW [00:00:00.571,472] <inf> main: Connection event. Num connections: 1
GW [00:00:00.621,307] <wrn> bt_conn: conn 0x20004f08 failed to establish. RF noise?
GW [00:00:00.621,459] <wrn> bt_mgmt: Security failed: level 1 err 9 
GW [00:00:00.621,459] <wrn> bt_mgmt: Failed to disconnect -128
GW [00:00:00.621,490] <wrn> bt_gatt: conn 0x20004f08 err 0x0e
GW [00:00:00.621,704] <inf> bt_mgmt: Disconnected: F5:FD:57:29:5F:67 (random), reason 0x3e 
GW [00:00:00.621,765] <inf> main: Disconnection event. Num connections: 0
GW [00:00:00.621,765] <wrn> unicast_client: Unknown connection disconnected
GW [00:00:00.621,917] <inf> bt_mgmt_scan: All bonded slots filled, will not accept new devices
GW [00:00:00.622,894] <inf> bt_mgmt_scan: Local addr: 77:BB:07:16:AE:49 (random). May time out. Updates not printed
GW [00:00:00.622,924] <inf> bt_mgmt_scan: Scanning successfully started
GW [00:00:00.627,349] <inf> bt_mgmt_scan: Creating connection to bonded device: F5:FD:57:29:5F:67 (random)
GW [00:00:00.632,843] <inf> bt_mgmt: Connected: F5:FD:57:29:5F:67 (random)
GW [00:00:00.632,873] <inf> main: Connection event. Num connections: 1
GW [00:00:00.712,768] <inf> main: Security changed
GW [00:00:00.764,373] <wrn> unicast_client: Got err: -61 from conn: 0x20004f08
GW [00:00:00.764,831] <inf> bt_mgmt_scan: All bonded slots filled, will not accept new devices
GW [00:00:00.766,113] <inf> bt_mgmt_scan: Local addr: 77:BB:07:16:AE:49 (random). May time out. Updates not printed
GW [00:00:00.766,113] <inf> bt_mgmt_scan: Scanning successfully started
GW [00:00:00.893,066] <inf> bt_vol_ctlr: VCS discover finished
GW [00:00:01.050,689] <inf> bt_mgmt_scan: Creating connection to bonded device: F0:D2:8E:F5:33:C2 (random)
GW [00:00:01.460,876] <inf> bt_mgmt: Connected: F0:D2:8E:F5:33:C2 (random)
GW [00:00:01.460,906] <inf> main: Connection event. Num connections: 2
GW [00:00:01.492,889] <inf> unicast_client: Discovered 1 sink endpoint(s) for device 0
GW [00:00:01.602,722] <inf> main: Security changed
GW [00:00:01.723,083] <wrn> unicast_client: Got err: -61 from conn: 0x20004ff0
GW [00:00:01.963,043] <inf> bt_vol_ctlr: VCS discover finished
GW [00:00:02.354,278] <inf> unicast_client: Discovered 1 source endpoint(s) for device 0
GW [00:00:02.414,276] <inf> unicast_client: LEFT sink stream configured
GW [00:00:02.414,306] <inf> le_audio: LC3 codec config for sink:
GW [00:00:02.414,306] <inf> le_audio:   Frequency: 24000 Hz
GW [00:00:02.414,306] <inf> le_audio:   Duration: 10000 us
GW [00:00:02.414,337] <inf> le_audio:   Channel allocation: 0x3
GW [00:00:02.414,337] <inf> le_audio:   Octets per frame: 60 (48000 bps)
GW [00:00:02.414,337] <inf> le_audio:   Frames per SDU: 1
GW [00:00:02.493,103] <inf> unicast_client: LEFT source stream configured
GW [00:00:02.493,133] <inf> le_audio: LC3 codec config for source:
GW [00:00:02.493,133] <inf> le_audio:   Frequency: 24000 Hz
GW [00:00:02.493,164] <inf> le_audio:   Duration: 10000 us
GW [00:00:02.493,164] <inf> le_audio:   Channel allocation: 0x1
GW [00:00:02.493,164] <inf> le_audio:   Octets per frame: 60 (48000 bps)
GW [00:00:02.493,164] <inf> le_audio:   Frames per SDU: 1
GW [00:00:02.722,625] <inf> unicast_client: Discovered 1 sink endpoint(s) for device 1
GW [00:00:03.173,767] <inf> unicast_client: Discovered 1 source endpoint(s) for device 1
GW [00:00:03.502,838] <inf> unicast_client: Stream 0x200121c4 started
GW [00:00:03.510,009] <inf> audio_usb: USB RX first data received.
GW [00:00:03.683,410] <inf> unicast_client: Stream 0x200122c4 started
GW [00:00:03.703,704] <inf> unicast_client: LEFT sink stream configured
GW [00:00:03.703,735] <inf> le_audio: LC3 codec config for sink:
GW [00:00:03.703,735] <inf> le_audio:   Frequency: 24000 Hz
GW [00:00:03.703,735] <inf> le_audio:   Duration: 10000 us
GW [00:00:03.703,735] <inf> le_audio:   Channel allocation: 0x3
GW [00:00:03.703,765] <inf> le_audio:   Octets per frame: 60 (48000 bps)
GW [00:00:03.703,765] <inf> le_audio:   Frames per SDU: 1
GW [00:00:03.703,765] <wrn> unicast_client: Failed to stop streams: -16, use default PD in preset
GW [00:00:03.703,796] <wrn> unicast_client: Presentation delay not set for LEFT device: -16
GW [00:00:03.723,724] <inf> unicast_client: LEFT source stream configured
GW [00:00:03.723,724] <inf> le_audio: LC3 codec config for source:
GW [00:00:03.723,724] <inf> le_audio:   Frequency: 24000 Hz
GW [00:00:03.723,754] <inf> le_audio:   Duration: 10000 us
GW [00:00:03.723,754] <inf> le_audio:   Channel allocation: 0x1
GW [00:00:03.723,754] <inf> le_audio:   Octets per frame: 60 (48000 bps)
GW [00:00:03.723,754] <inf> le_audio:   Frames per SDU: 1
GW [00:00:03.872,680] <inf> unicast_client: Stream 0x200123dc started
GW [00:00:03.893,157] <inf> unicast_client: Stream 0x200124dc started
GW [00:00:03.930,511] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1
GW [00:00:08.570,495] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 101
GW [00:00:13.349,426] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 201
GW [00:00:18.389,556] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 301
GW [00:00:23.189,392] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 401
GW [00:00:27.589,385] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 501
GW [00:00:32.229,400] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 601
GW [00:00:36.949,401] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 701
GW [00:00:41.679,382] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 801
GW [00:00:46.639,495] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 901
GW [00:00:51.339,416] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1001
GW [00:00:56.159,393] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1101
GW [00:01:00.749,389] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1201
GW [00:01:05.689,392] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1301
GW [00:01:10.389,404] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1401
GW [00:01:15.309,539] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1501
GW [00:01:20.539,672] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1601
GW [00:01:25.609,405] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1701
GW [00:01:30.719,696] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1801
GW [00:01:35.719,665] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 1901
GW [00:01:40.479,400] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2001
GW [00:01:45.399,719] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2101
GW [00:01:50.359,619] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2201
GW [00:01:55.369,750] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2301
GW [00:02:00.839,782] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2401
GW [00:02:06.339,447] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2501
GW [00:02:11.549,377] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2601
GW [00:02:16.719,451] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2701
GW [00:02:22.029,479] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2801
GW [00:02:27.319,396] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 2901
GW [00:02:32.469,390] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3001
GW [00:02:37.449,401] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3101
GW [00:02:42.619,384] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3201
GW [00:02:47.639,465] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3301
GW [00:02:52.749,481] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3401
GW [00:02:57.949,401] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3501
GW [00:03:03.229,400] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3601
GW [00:03:08.389,404] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3701
GW [00:03:13.569,396] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3801
GW [00:03:18.420,501] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 3901
GW [00:03:23.489,471] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4001
GW [00:03:28.899,383] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4101
GW [00:03:34.209,381] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4201
GW [00:03:39.309,387] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4301
GW [00:03:44.350,524] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4401
GW [00:03:48.949,432] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4501
GW [00:03:53.799,560] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4601
GW [00:03:58.679,382] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4701
GW [00:04:03.579,406] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4801
GW [00:04:08.389,373] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 4901
GW [00:04:13.269,378] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5001
GW [00:04:18.200,500] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5101
GW [00:04:23.249,542] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5201
GW [00:04:28.329,376] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5301
GW [00:04:33.139,404] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5401
GW [00:04:37.999,389] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5501
GW [00:04:42.769,378] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5601
GW [00:04:47.639,404] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5701
GW [00:04:52.739,532] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5801
GW [00:04:58.009,399] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 5901
GW [00:05:02.839,385] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6001
GW [00:05:07.719,390] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6101
GW [00:05:12.659,393] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6201
GW [00:05:17.329,376] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6301
GW [00:05:22.719,543] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6401
GW [00:05:27.989,379] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6501
GW [00:05:32.819,396] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6601
GW [00:05:37.469,390] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6701
GW [00:05:42.109,375] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6801
GW [00:05:46.609,405] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 6901
GW [00:05:51.229,522] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7001
GW [00:05:56.069,396] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7101
GW [00:06:00.609,375] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7201
GW [00:06:05.449,401] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7301
GW [00:06:10.229,461] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7401
GW [00:06:14.989,379] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7501
GW [00:06:19.859,710] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7601
GW [00:06:24.699,676] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7701
GW [00:06:29.589,843] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7801
GW [00:06:34.629,699] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 7901
GW [00:06:39.629,638] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8001
GW [00:06:44.479,553] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8101
GW [00:06:49.589,660] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8201
GW [00:06:54.449,401] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8301
GW [00:06:59.739,776] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8401
GW [00:07:04.879,455] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8501
GW [00:07:09.869,415] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8601
GW [00:07:14.469,451] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8701
GW [00:07:19.529,479] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8801
GW [00:07:24.349,395] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 8901
GW [00:07:29.259,399] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9001
GW [00:07:34.029,388] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9101
GW [00:07:38.909,423] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9201
GW [00:07:43.069,427] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9301
GW [00:07:47.259,552] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9401
GW [00:07:53.706,573] <inf> audio_usb: USB TX first data sent.
GW [00:08:04.819,396] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9501
GW [00:08:08.249,389] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9601
GW [00:08:11.459,442] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9701
GW [00:08:14.939,514] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9801
GW [00:08:18.109,405] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 9901
GW [00:08:21.669,403] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 10001
GW [00:08:25.259,399] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 10101
GW [00:08:28.759,399] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 10201
GW [00:08:32.149,383] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 10301
GW [00:08:35.499,389] <wrn> le_audio_rx: BLE ISO RX overrun: Num: 10401


    *** Using Zephyr OS v3.7.99-0bc3393fb112 ***
HR [00:00:00.276,885] <inf> board_version: Compatible board/HW version found: 1.0.0
HR [00:00:00.309,143] <inf> fw_info: 
         nRF5340 Audio nRF5340 Audio DK cpuapp                      
         NCS base version: 2.8.0                            
         Cmake run : Fri Jan 03 19:31:25 2025
HR [00:00:00.309,143] <inf> fw_info: ------- DEBUG BUILD -------
HR [00:00:00.309,173] <inf> fw_info: HEADSET right device
HR [00:00:00.378,906] <inf> bt_keys: SC LTK: 0xb589a7752caaa3535c4ca66003e0dbde
HR [00:00:00.381,042] <inf> bt_mgmt_ctlr_cfg: Controller: SoftDevice: Version 6.0 (0x0e), Revision 8270
HR [00:00:00.381,256] <inf> bt_mgmt: Local identity addr: F0:D2:8E:F5:33:C2 (random)
HR [00:00:00.386,932] <inf> bt_mgmt_adv: Local addr: 58:9D:62:7D:93:2D (random)
HR [00:00:00.387,023] <inf> bt_mgmt_adv: Adv directed to: D3:C8:9D:D1:BE:66 (random).
HR [00:00:00.387,603] <inf> bt_mgmt_adv: Advertising successfully started
HR [00:00:01.668,121] <inf> bt_mgmt: Directed adv timed out with no connection, reverting to normal adv
HR [00:00:01.671,417] <inf> bt_mgmt_adv: Local addr: 6B:51:7A:41:F2:CA (random)
HR [00:00:01.671,936] <inf> bt_mgmt_adv: Advertising successfully started
HR [00:00:02.517,425] <inf> bt_mgmt: Connected: D3:C8:9D:D1:BE:66 (random)
HR [00:00:02.517,456] <inf> main: Connection event. Num connections: 1
HR [00:00:02.660,308] <inf> main: Security changed
HR [00:00:02.660,522] <wrn> bt_gatt: Device is not subscribed to characteristic
HR [00:00:02.660,522] <wrn> bt_pacs: PACS notify failed: -22
HR [00:00:02.660,552] <wrn> bt_gatt: Device is not subscribed to characteristic
HR [00:00:02.660,552] <wrn> bt_pacs: PACS notify failed: -22
HR [00:00:03.630,645] <inf> bt_content_ctrl_media: Discovery of MCS finished
HR [00:00:04.750,885] <inf> le_audio: LC3 codec config for sink:
HR [00:00:04.750,915] <inf> le_audio:   Frequency: 24000 Hz
HR [00:00:04.750,915] <inf> le_audio:   Duration: 10000 us
HR [00:00:04.750,915] <inf> le_audio:   Channel allocation: 0x3
HR [00:00:04.750,915] <inf> le_audio:   Octets per frame: 60 (48000 bps)
HR [00:00:04.750,915] <inf> le_audio:   Frames per SDU: 1
HR [00:00:04.770,843] <inf> le_audio: LC3 codec config for source:
HR [00:00:04.770,843] <inf> le_audio:   Frequency: 24000 Hz
HR [00:00:04.770,843] <inf> le_audio:   Duration: 10000 us
HR [00:00:04.770,843] <inf> le_audio:   Channel allocation: 0x1
HR [00:00:04.770,874] <inf> le_audio:   Octets per frame: 60 (48000 bps)
HR [00:00:04.770,874] <inf> le_audio:   Frames per SDU: 1
HR [00:00:04.791,412] <inf> main: Presentation delay 5000 us is set by initiator
HR [00:00:04.791,442] <inf> main: Presentation delay 5000 us is set by initiator
HR [00:00:04.903,472] <inf> unicast_server: Stream 0x200105f4 started
HR [00:00:04.905,120] <wrn> le_audio_rx: Not in streaming state (1), thrown 1 packet(s)
DAC L gain 112   
ADC L gain 112   
DAC R gain 112   
ADC R gain 112   
HR [00:00:04.935,211] <wrn> audio_datapath: I2S RX overrun. Single msg
HR [00:00:04.939,178] <wrn> audio_datapath: Data received, total under-runs: 11
HR [00:00:04.940,582] <inf> unicast_server: Stream 0x2001061c started
HR [00:00:04.941,192] <wrn> audio_datapath: I2S RX continuing stream
HR [00:00:04.946,197] <inf> audio_datapath: Drft comp state: CALIB
HR [00:00:04.950,195] <wrn> audio_datapath: Data received, total under-runs: 12
HR [00:00:05.046,203] <inf> audio_datapath: Drft comp state: OFFSET
HR [00:00:05.421,051] <wrn> audio_datapath: Data received, total under-runs: 13
HR [00:00:05.446,075] <inf> audio_datapath: Drft comp state: LOCKED
HR [00:00:05.455,413] <inf> audio_datapath: Pres comp state: MEAS
HR [00:00:05.565,277] <inf> audio_datapath: Pres comp state: WAIT
HR [00:00:05.705,322] <inf> audio_datapath: Pres comp state: INIT
HR [00:00:05.715,240] <inf> audio_datapath: Pres comp state: MEAS
HR [00:00:05.825,225] <inf> audio_datapath: Pres comp state: LOCKED

  • 0 in reply to Abdulmohaimen

    Hi Abdulmohaimen,

    Abdulmohaimen said:
    Currently, when using the accelerated microphone signal while the headset is streaming sound, the microphone volume is too low. (Current setup i have CIS mode with some limitions -  accelerated microphone signal  and Channel disconncating as well as the LOW mic when the sound on headphones)

    Can you provide details about accelerated microphone signal? 
    Is recorded microphone signal on the same or on the other device?
    How much is the signal accelerated?
    Do you use the same sample rate for recording and playback?

    Best regards,
    Dejan

Related
Terms of service