• State Not Answered
  • Replies 29 replies
  • Subscribers 76 subscribers
  • Views 1310 views
  • Users 0 members are here
Attachments (0)
Nordic Case Info
  • Case ID: 346368
Options

MISO line mimics the MOSI line in SPIM configuration sdk 17.1.0

omerBzkrt

Hi,

When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration works properly. Before message transfer CS pin goes low, and after that, the MOSI line works. I can read message that I sent using the oscilloscope.

What can be the problem with the MISO line signal reflecting the MOSI line signal? The SPI config stage CPOL = 0, CPAH = 1, I am using a 2 MHz clock signal. Thanks for your help.

Parents
  • 0

    Schematic. Looks to me like MISO was never driven at all and is just floating. The voltage change results from coupling to MOSI and clock signal.

    MISO is supposed to be driven by the slave when CS=Low. Check that its properly connected. 

  • 0 in reply to Turbo J

    Sorry for the late response. All physical pins are connected properly, but I did not understand the problem. During the SPIM configuration, I just initialised the MISO pin. I am sharing my ADS1299 library code with you, Maybe the issue is about the software configuration of the SPIM. I checked the working mechanism of the SPI with ADS1299, and it looks like it was working properly. Again, thanks for your help.

     

    #include "ADS1299_nRF.h"
#include <nrf.h>
#include <nrf_log.h>
#include <nrf_log_ctrl.h>
#include <nrf_log_default_backends.h>
#include <nrf_gpio.h>
#include <nrf_delay.h>
#include "ads1299_delay.h"

// Enable polling mode for DRDY
#define POLL_DREADY

#define SPIM2 NRF_SPIM2

bool new_data_available = false;
uint8_t rx_buffer[27], tx_buffer[8];
uint8_t sample_number = 0;
static uint8_t regData[24]; // Mirror of ADS1299 registers


/** @brief SPI interface initialization. Accurate timing use HFCLK clock */
void spi_init(void) {
    // Start HFCLK source for accurate timing
    NRF_CLOCK->TASKS_HFCLKSTART = 1;
    while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);
    NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
    
    // Disable SPIM to configure it
    SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Disabled << SPIM_ENABLE_ENABLE_Pos);

    // Configure SPIM2 pins
    SPIM2->PSEL.SCK = PIN_SCK;
    SPIM2->PSEL.MOSI = PIN_MOSI;
    SPIM2->PSEL.MISO = PIN_MISO;
    
    SPIM2->FREQUENCY = SPIM_FREQUENCY_FREQUENCY_M2; // 2 MHz

    // ADS1299 set Data mode clock polarity = 0; clock_phase = 1
    SPIM2->CONFIG = (SPIM_CONFIG_CPOL_ActiveLow << SPIM_CONFIG_CPOL_Pos) |  // Fixed CPOL
                    (SPIM_CONFIG_CPHA_Trailing << SPIM_CONFIG_CPHA_Pos) |
                    (SPIM_CONFIG_ORDER_MsbFirst << SPIM_CONFIG_ORDER_Pos);

    SPIM2->EVENTS_END = 0;
    SPIM2->EVENTS_ENDTX = 0;
    SPIM2->EVENTS_ENDRX = 0;
    SPIM2->EVENTS_STOPPED = 0;

    SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Enabled << SPIM_ENABLE_ENABLE_Pos);
    
}

static void spi_uninit(void) {
    SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Disabled << SPIM_ENABLE_ENABLE_Pos);
    nrf_gpio_cfg_input(PIN_SCK, NRF_GPIO_PIN_NOPULL);
    nrf_gpio_cfg_input(PIN_MOSI, NRF_GPIO_PIN_NOPULL);
    nrf_gpio_cfg_input(PIN_MISO, NRF_GPIO_PIN_NOPULL);
}

//bool spi_transfer_byte(uint8_t tx, uint8_t *rx) {
//    uint8_t local_rx = 0;
//    if (!rx) rx = &local_rx;
//    if (!(SPIM2->ENABLE & SPIM_ENABLE_ENABLE_Msk)) {
//        SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Enabled << SPIM_ENABLE_ENABLE_Pos);
//    }
//    SPIM2->TXD.PTR = (uint32_t)&tx;
//    SPIM2->TXD.MAXCNT = 1;
//    SPIM2->RXD.PTR = (uint32_t)rx;
//    SPIM2->RXD.MAXCNT = 1;
//    SPIM2->EVENTS_END = 0;
//    SPIM2->TASKS_START = 1;

//    nrf_delay_us(20);

//    //uint32_t timeout = 10000;
//    //while (!SPIM2->EVENTS_END && timeout--) {
//    //    nrf_delay_us(1);
//    //}
//    //if (timeout == 0) {
//    //    NRF_LOG_ERROR("SPI transfer timeout");
//    //    return false;
//    //}
//    SPIM2->EVENTS_END = 0;
//    NRF_LOG_INFO("SPI TX: 0x%02x, RX: 0x%02x", tx, *rx);
//    return true;
//}

uint8_t spi_transfer_byte(uint8_t tx) {
    uint8_t rx;
    if (!(SPIM2->ENABLE & SPIM_ENABLE_ENABLE_Msk)) {
        SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Enabled << SPIM_ENABLE_ENABLE_Pos);
    }
    SPIM2->TXD.PTR = (uint32_t)&tx;
    SPIM2->TXD.MAXCNT = 1;
    SPIM2->RXD.PTR = (uint32_t)&rx;
    SPIM2->RXD.MAXCNT = 1;
    SPIM2->EVENTS_END = 0;
    SPIM2->TASKS_START = 1;
    while (!SPIM2->EVENTS_END);
    SPIM2->EVENTS_END = 0;
    //SPIM2->TASKS_STOP = 1;
    NRF_LOG_INFO("SPI TX: 0x%02x, RX: 0x%02x", tx, rx);
    return rx;
}

bool spi_transfer_byte_v2(uint8_t tx, uint8_t *rx) {
    uint8_t local_rx = 0;
    if (!rx) rx = &local_rx;
    
    // Ensure SPIM2 is enabled (assumes prior configuration)
    if (!(SPIM2->ENABLE & SPIM_ENABLE_ENABLE_Msk)) {
        SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Enabled << SPIM_ENABLE_ENABLE_Pos);
    }
    
    // Clear events before starting
    SPIM2->EVENTS_ENDTX = 0;
    SPIM2->EVENTS_ENDRX = 0;
    SPIM2->EVENTS_END = 0;
    
    // Configure buffers
    SPIM2->TXD.PTR = (uint32_t)&tx;
    SPIM2->TXD.MAXCNT = 1;
    SPIM2->RXD.PTR = (uint32_t)rx;
    SPIM2->RXD.MAXCNT = 1;
    
    // Start transaction
    SPIM2->TASKS_START = 1;
    
    // Wait for transaction to complete
    while (!SPIM2->EVENTS_END);
    
    // Clear events
    SPIM2->EVENTS_ENDTX = 0;
    SPIM2->EVENTS_ENDRX = 0;
    SPIM2->EVENTS_END = 0;

    NRF_LOG_INFO("SPI TX: 0x%02x, RX: 0x%02x", tx, *rx);
    return true;
}

bool ADS1299_init(void) {
    
    // recommended power up sequence for ADS1299
    delay_init();
    nrf_delay_ms(50);
    
    NRF_LOG_INFO("Initializing ADS1299");
    nrf_gpio_pin_clear(RESET_PIN);
    nrf_gpio_cfg_output(RESET_PIN);
    nrf_gpio_pin_clear(RESET_PIN);
    nrf_delay_us(4);
    nrf_gpio_pin_set(RESET_PIN);
    nrf_delay_us(20);
    
    //nrf_gpio_cfg_output(PIN_SCK);
    //nrf_gpio_cfg_output(PIN_MOSI);
    
    //nrf_gpio_pin_clear(PIN_SCK);
    //nrf_gpio_pin_clear(PIN_MOSI);
    
    spi_init();

    nrf_gpio_cfg_input(PIN_DRDY,NRF_GPIO_PIN_NOPULL);

    nrf_gpio_pin_set(CS_PIN);
    //NRF_GPIO->PIN_CNF[CS_PIN] = (GPIO_PIN_CNF_DIR_Output << GPIO_PIN_CNF_DIR_Pos) |
    //                            (GPIO_PIN_CNF_DRIVE_S0S1 << GPIO_PIN_CNF_DRIVE_Pos) |
    //                            (GPIO_PIN_CNF_INPUT_Connect << GPIO_PIN_CNF_INPUT_Pos) |
    //                            (GPIO_PIN_CNF_PULL_Disabled << GPIO_PIN_CNF_PULL_Pos) |
    //                            (GPIO_PIN_CNF_SENSE_Disabled << GPIO_PIN_CNF_SENSE_Pos);

    nrf_gpio_cfg_output(CS_PIN);

    nrf_gpio_pin_set(CS_PIN);
    nrf_gpio_pin_set(RESET_PIN);

    NRF_LOG_INFO("SPI init success");
#ifdef POLL_DREADY
    NRF_LOG_INFO("DRDY polling enabled");
#else
    NRF_LOG_INFO("DRDY interrupt not implemented");
#endif
    return true;
}

void poll_dready(void) {
#ifdef POLL_DREADY
    NRF_LOG_INFO("Polling DRDY, state: %d", nrf_gpio_pin_read(PIN_DRDY));
    if (nrf_gpio_pin_read(PIN_DRDY) == 0) {
        NRF_LOG_INFO("DRDY low, receiving data");
        ADS1299_receive_data();
        send_new_available_data();
    }
#endif
}

bool ADS1299_write_register(uint8_t address, uint8_t value) {

    uint8_t opcode1 = address | COMMAND_WREG;
    nrf_gpio_pin_clear(CS_PIN);

    //if (!spi_transfer_byte_v2(opcode1, NULL)) {
    //    nrf_gpio_pin_set(CS_PIN);
    //    return false;
    //}
    //if (!spi_transfer_byte_v2(0x00, NULL)) {
    //    nrf_gpio_pin_set(CS_PIN);
    //    return false;
    //}
    //if (!spi_transfer_byte_v2(value, NULL)) {
    //    nrf_gpio_pin_set(CS_PIN);
    //    return false;
    //}
    
    spi_transfer_byte(opcode1);
    spi_transfer_byte(0x00);
    spi_transfer_byte(value);
    nrf_delay_us(4);
    nrf_gpio_pin_set(CS_PIN);
    regData[address] = value;
    
    
    return true;
}

bool ADS1299_read_register(uint8_t address, uint8_t *value) {
    uint8_t opcode1 = address | COMMAND_RREG;
    
    nrf_gpio_pin_clear(CS_PIN);

    //if (!spi_transfer_byte_v2(opcode1, NULL)) {
    //    nrf_gpio_pin_set(CS_PIN);
    //    return false;
    //}
    //if (!spi_transfer_byte_v2(0x00, NULL)) {
    //    nrf_gpio_pin_set(CS_PIN);
    //    return false;
    //}
    //if (!spi_transfer_byte_v2(0x00, value)) {
    //    nrf_gpio_pin_set(CS_PIN);
    //    return false;
    //}
    
    spi_transfer_byte(opcode1);
    spi_transfer_byte(0x00);
    *value = spi_transfer_byte(0x00);

    nrf_delay_us(4);

    nrf_gpio_pin_set(CS_PIN);

    regData[address] = *value;
    
    return true;
}

bool ADS1299_send_command(uint8_t command) {
    uint8_t dummy;
    nrf_gpio_pin_clear(CS_PIN);
    //if (!spi_transfer_byte_v2(command, &dummy)) {
    //    NRF_LOG_ERROR("Failed to send command 0x%02x", command);
    //    nrf_gpio_pin_set(CS_PIN);
    //    return false;
    //}
    spi_transfer_byte(command);

    nrf_delay_us(4);
    nrf_gpio_pin_set(CS_PIN);
    return true;
}

bool ADS1299_send_start(void) {

    bool result = ADS1299_send_command(COMMAND_START);    
    return result;
}

bool ADS1299_send_read_continuous(void) {
    bool result = ADS1299_send_command(COMMAND_RDATAC);
    nrf_delay_us(3);
    return result;
}

bool ADS1299_send_reset(void) {
    //nrf_gpio_pin_clear(CS_PIN);
    bool result = ADS1299_send_command(COMMAND_RESET);
    nrf_delay_us(20);
    //nrf_gpio_pin_set(CS_PIN);
    NRF_LOG_INFO("Reset command sent, result: %d", result);
    return result;
}

bool ADS1299_send_sdatac(void) {
    //nrf_gpio_pin_clear(CS_PIN);
    bool result = ADS1299_send_command(COMMAND_SDATAC);
    //nrf_gpio_pin_set(CS_PIN);
    nrf_delay_ms(10);
    NRF_LOG_INFO("Stop read continuously command sent, result: %d", result);
    return result;
}

bool ADS1299_receive_data(void) {
    new_data_available = false;
    if (!spi_transfer_bytes(NULL, rx_buffer, 27)) {
        NRF_LOG_ERROR("Failed to receive data");
        return false;
    }
    new_data_available = true;
    NRF_LOG_INFO("Data received, triggering send_new_available_data");
    return true;
}

bool ADS1299_poll_new_data(ADS1299_data_t *data) {
    if (new_data_available) {
        new_data_available = false;
        *data = ADS1299_convert_data();
        return true;
    }
    return false;
}

static inline int32_t buffer_to_channel(uint8_t id) {
    int32_t value = (rx_buffer[3 + id * 3] << 16) | (rx_buffer[4 + id * 3] << 8) | rx_buffer[5 + id * 3];
    if (value & 0x00800000) {
        value |= 0xFF000000;
    } else {
        value &= 0x00FFFFFF;
    }
    return value;
}

ADS1299_data_t ADS1299_convert_data(void) {
    ADS1299_data_t data;
    data.lead_off_positive = rx_buffer[0] << 4;
    data.lead_off_positive |= (rx_buffer[1] & 0b11110000) >> 4;
    data.lead_off_negative = rx_buffer[1] << 4;
    data.lead_off_negative |= (rx_buffer[2] & 0b11110000) >> 4;
    data.gpio_0 = rx_buffer[2] & 0b00001000;
    data.gpio_1 = rx_buffer[2] & 0b00000100;
    data.gpio_2 = rx_buffer[2] & 0b00000010;
    data.gpio_3 = rx_buffer[2] & 0b00000001;
    data.channel_0 = buffer_to_channel(0);
    data.channel_1 = buffer_to_channel(1);
    data.channel_2 = buffer_to_channel(2);
    data.channel_3 = buffer_to_channel(3);
    data.channel_4 = buffer_to_channel(4);
    data.channel_5 = buffer_to_channel(5);
    data.channel_6 = buffer_to_channel(6);
    data.channel_7 = buffer_to_channel(7);
    return data;
}

void send_new_available_data(void) {
    if (new_data_available) {
        new_data_available = false;
        NRF_LOG_INFO("Sample: %d", sample_number++);
        for (uint8_t i = 0; i < 27; i++) {
            NRF_LOG_INFO("Byte %d: 0x%02x", i, rx_buffer[i]);
        }
    }
}

  • 0 in reply to hmolesworth

    I already shared my ADS1299_nRF.c file code. The main code includes ADS1299 start procedures.

    The code goes like this

    ADS1299_init();

    ADS1299_send_reset();

    ADS1299_send_sdatac();

    uint8_t id;

    ADS1299_read_register(0x00, &id);

  • 0 in reply to omerBzkrt

    The code (you shared) contains none of the suggestions we made then? If it does have the suggestions, without having sight of the changes we are blind as to providing any feedback. One other suggestion, if I may, is that all measurements for SCK, /CS and MOSI should be as close to the ADS1299 pins as possible, not at the nRF52.

  • 0 in reply to hmolesworth

    The clock frequency is 2 MHz. These are the latest configuration results that I got from the logic analyser. 

    This is my connection actually, I am getting the result in the middle of the two pins between ADS1299 and nRF52840DK. 

    According to your suggestions, this is my code's latest state. 

    #include "ADS1299_nRF.h"
#include <nrf.h>
#include <nrf_log.h>
#include <nrf_log_ctrl.h>
#include <nrf_log_default_backends.h>
#include <nrf_gpio.h>
#include <nrf_delay.h>
#include "ads1299_delay.h"

// Enable polling mode for DRDY
#define POLL_DREADY

#define SPIM2 NRF_SPIM2

bool new_data_available = false;
uint8_t rx_buffer[27], tx_buffer[8];
uint8_t sample_number = 0;
static uint8_t regData[24]; // Mirror of ADS1299 registers

/** @brief SPI interface initialization. Accurate timing use HFCLK clock */
void spi_init(void) {
    // Start HFCLK source for accurate timing
    NRF_CLOCK->TASKS_HFCLKSTART = 1;
    while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);
    NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;
    
    // Disable SPIM to configure it
    SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Disabled << SPIM_ENABLE_ENABLE_Pos);
    
    NRF_P0->OUTSET = (1 << CS_PIN);

    // Set High-drive pin mode for SPI
    nrf_gpio_cfg(PIN_SCK,  NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_CONNECT, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_H0H1, NRF_GPIO_PIN_NOSENSE);
    nrf_gpio_cfg(PIN_MOSI, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_CONNECT, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_H0H1, NRF_GPIO_PIN_NOSENSE);
    nrf_gpio_cfg(CS_PIN,   NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_CONNECT, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_H0H1, NRF_GPIO_PIN_NOSENSE);
    nrf_gpio_cfg(PIN_MISO, NRF_GPIO_PIN_DIR_INPUT,  NRF_GPIO_PIN_INPUT_CONNECT, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_H0H1, NRF_GPIO_PIN_NOSENSE);

    NRF_P0->OUTSET = (1 << CS_PIN);

    // Configure SPIM2 pins
    SPIM2->PSEL.SCK = PIN_SCK;
    SPIM2->PSEL.MOSI = PIN_MOSI;
    SPIM2->PSEL.MISO = PIN_MISO;

    SPIM2->FREQUENCY = SPIM_FREQUENCY_FREQUENCY_M2; // 2 MHz (t_CLK = 500 ns)
    
    SPIM2->ORC = 0xFF;

    // ADS1299 set Data mode: clock polarity = 0, clock phase = 1
    SPIM2->CONFIG = (SPIM_CONFIG_CPOL_ActiveHigh << SPIM_CONFIG_CPOL_Pos) |  // CPOL = 0
                    (SPIM_CONFIG_CPHA_Trailing << SPIM_CONFIG_CPHA_Pos) |     // CPHA = 1
                    (SPIM_CONFIG_ORDER_MsbFirst << SPIM_CONFIG_ORDER_Pos);
    
    SPIM2->EVENTS_END = 0;
    SPIM2->EVENTS_ENDTX = 0;
    SPIM2->EVENTS_ENDRX = 0;
    
    SPIM2->INTENCLR = 0xFFFFFFFFUL;
    SPIM2->INTENSET = 0x040;
    
    SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Enabled << SPIM_ENABLE_ENABLE_Pos);
}

static void spi_uninit(void) {
    SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Disabled << SPIM_ENABLE_ENABLE_Pos);
    nrf_gpio_cfg_input(PIN_SCK, NRF_GPIO_PIN_NOPULL);
    nrf_gpio_cfg_input(PIN_MOSI, NRF_GPIO_PIN_NOPULL);
    nrf_gpio_cfg_input(PIN_MISO, NRF_GPIO_PIN_NOPULL);
}

uint8_t spi_transfer_byte(uint8_t tx) {
    uint8_t rx;
    memset(&rx, 0, sizeof(rx));
    if (!(SPIM2->ENABLE & SPIM_ENABLE_ENABLE_Msk)) {
        SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Enabled << SPIM_ENABLE_ENABLE_Pos);
    }
    // Clear events before starting
    SPIM2->EVENTS_ENDTX = 0;
    SPIM2->EVENTS_ENDRX = 0;
    SPIM2->EVENTS_END = 0;
    
    // Configure buffers
    SPIM2->TXD.PTR = (uint32_t)&tx;
    SPIM2->TXD.MAXCNT = 1;
    SPIM2->RXD.PTR = (uint32_t)&rx;
    SPIM2->RXD.MAXCNT = 1;
    
    // Start transaction
    SPIM2->TASKS_START = 1;
    
    // Wait for transaction to complete
    while (!SPIM2->EVENTS_ENDTX);
    while (!SPIM2->EVENTS_ENDRX);
    while (!(SPIM2->EVENTS_END));

    nrf_delay_us(2); // t_CSH: Minimum 1 µs hold time after SCLK falling edge
    
    NRF_LOG_INFO("SPI TX: 0x%02x, RX: 0x%02x", tx, rx);
    return rx;
}

bool spi_transfer_bytes(const uint8_t *tx, uint8_t *rx, size_t len) {
    if (!(SPIM2->ENABLE & SPIM_ENABLE_ENABLE_Msk)) {
        SPIM2->ENABLE = (SPIM_ENABLE_ENABLE_Enabled << SPIM_ENABLE_ENABLE_Pos);
    }
    
    static uint8_t dummy_tx = 0xFF;
    static uint8_t dummy_rx;

    SPIM2->EVENTS_END = 0;
    SPIM2->TXD.PTR = (uint32_t)(tx ? tx : &dummy_tx);
    SPIM2->TXD.MAXCNT = len;
    SPIM2->RXD.PTR = (uint32_t)(rx ? rx : &dummy_rx);
    SPIM2->RXD.MAXCNT = len;

    SPIM2->TASKS_START = 1;
    while (!SPIM2->EVENTS_END);
    SPIM2->ENABLE = SPIM_ENABLE_ENABLE_Disabled; // Disable SPIM to allow pull-up to take effect
    return true;
}

void ADS1299_pwr_up_seq(void)
{
    nrf_delay_ms(40);
    nrf_gpio_cfg(RESET_PIN, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_DISCONNECT, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_H0H1, NRF_GPIO_PIN_NOSENSE);
    nrf_gpio_pin_clear(RESET_PIN);
    nrf_delay_us(2);
    nrf_gpio_pin_set(RESET_PIN);
    nrf_delay_us(10);
}

bool ADS1299_init(void) {
    // Recommended power-up sequence for ADS1299
    
    NRF_LOG_INFO("Initializing ADS1299");
    ADS1299_pwr_up_seq();
    nrf_delay_ms(1000);
    ADS1299_pwr_up_seq();
    
    spi_init();

    nrf_gpio_cfg_input(PIN_DRDY, NRF_GPIO_PIN_NOPULL);

    NRF_LOG_INFO("SPI init success");
#ifdef POLL_DREADY
    NRF_LOG_INFO("DRDY polling enabled");
#else
    NRF_LOG_INFO("DRDY interrupt not implemented");
#endif
    return true;
}

void poll_dready(void) {
#ifdef POLL_DREADY
    NRF_LOG_INFO("Polling DRDY, state: %d", nrf_gpio_pin_read(PIN_DRDY));
    if (nrf_gpio_pin_read(PIN_DRDY) == 0) {
        NRF_LOG_INFO("DRDY low, receiving data");
        ADS1299_receive_data();
        send_new_available_data();
    }
#endif
}

bool ADS1299_write_register(uint8_t address, uint8_t value) {

    uint8_t cmd[] = {
        (uint8_t)(address | COMMAND_WREG),
        0x00, // Write 1 register
        value
    };

    nrf_gpio_pin_clear(CS_PIN);
    nrf_delay_us(6); // t_CSSC: Delay from CS low to first SCLK (min 6 ns, use 50 ns for safety)
    spi_transfer_bytes(cmd, NULL, sizeof(cmd));
    nrf_delay_us(1); // t_CSH: Delay from last SCLK to CS high (min 1 µs)
    nrf_gpio_pin_set(CS_PIN);
    nrf_delay_us(1); // t_CSH hold time after CS high

    regData[address] = value;
    return true;
}

bool ADS1299_read_register(uint8_t address, uint8_t *value) {
    //uint8_t tx_buf[] = {
    //    (uint8_t)(address | COMMAND_RREG),
    //    0x00,  // Read 1 register
    //    0x00   // Dummy byte for response
    //};
    //uint8_t rx_buf[3] = {0};
    
    uint8_t opcode1 = (address | 0x20);
    nrf_gpio_pin_clear(CS_PIN);
    spi_transfer_byte(opcode1);
    spi_transfer_byte(0x00);
    *value = spi_transfer_byte(0x00);
    nrf_gpio_pin_set(CS_PIN);
    nrf_delay_us(1); // t_CSH hold time after CS high

    regData[address] = *value;
    return true;
}

bool ADS1299_send_command(uint8_t command) {
    uint8_t dummy;
    nrf_gpio_pin_clear(CS_PIN);
    spi_transfer_byte(command);
    nrf_gpio_pin_set(CS_PIN);
    nrf_delay_us(1); // t_CSH hold time after CS high
    return true;
}

bool ADS1299_send_start(void) {
    bool result = ADS1299_send_command(COMMAND_START);    
    return result;
}

bool ADS1299_send_read_continuous(void) {
    bool result = ADS1299_send_command(COMMAND_RDATAC);
    nrf_delay_us(3); // Allow RDATAC to settle
    return result;
}

bool ADS1299_send_reset(void) {
    bool result = ADS1299_send_command(COMMAND_RESET);
    NRF_LOG_INFO("Reset command sent, result: %d", result);
    return result;
}

bool ADS1299_send_sdatac(void) {
    bool result = ADS1299_send_command(COMMAND_SDATAC);
    NRF_LOG_INFO("Stop read continuously command sent, result: %d", result);
    return result;
}

bool ADS1299_receive_data(void) {
    new_data_available = false;
    if (!spi_transfer_bytes(NULL, rx_buffer, 27)) {
        NRF_LOG_ERROR("Failed to receive data");
        return false;
    }
    new_data_available = true;
    NRF_LOG_INFO("Data received, triggering send_new_available_data");
    return true;
}

bool ADS1299_poll_new_data(ADS1299_data_t *data) {
    if (new_data_available) {
        new_data_available = false;
        *data = ADS1299_convert_data();
        return true;
    }
    return false;
}

static inline int32_t buffer_to_channel(uint8_t id) {
    int32_t value = (rx_buffer[3 + id * 3] << 16) | (rx_buffer[4 + id * 3] << 8) | rx_buffer[5 + id * 3];
    if (value & 0x00800000) {
        value |= 0xFF000000;
    } else {
        value &= 0x00FFFFFF;
    }
    return value;
}

ADS1299_data_t ADS1299_convert_data(void) {
    ADS1299_data_t data;
    data.lead_off_positive = rx_buffer[0] << 4;
    data.lead_off_positive |= (rx_buffer[1] & 0b11110000) >> 4;
    data.lead_off_negative = rx_buffer[1] << 4;
    data.lead_off_negative |= (rx_buffer[2] & 0b11110000) >> 4;
    data.gpio_0 = rx_buffer[2] & 0b00001000;
    data.gpio_1 = rx_buffer[2] & 0b00000100;
    data.gpio_2 = rx_buffer[2] & 0b00000010;
    data.gpio_3 = rx_buffer[2] & 0b00000001;
    data.channel_0 = buffer_to_channel(0);
    data.channel_1 = buffer_to_channel(1);
    data.channel_2 = buffer_to_channel(2);
    data.channel_3 = buffer_to_channel(3);
    data.channel_4 = buffer_to_channel(4);
    data.channel_5 = buffer_to_channel(5);
    data.channel_6 = buffer_to_channel(6);
    data.channel_7 = buffer_to_channel(7);
    return data;
}

void send_new_available_data(void) {
    if (new_data_available) {
        new_data_available = false;
        NRF_LOG_INFO("Sample: %d", sample_number++);
        for (uint8_t i = 0; i < 27; i++) {
            NRF_LOG_INFO("Byte %d: 0x%02x", i, rx_buffer[i]);
        }
    }
}


    And this code part is my main.

    #include <nrf.h>
#include <nrf_log.h>
#include <nrf_log_ctrl.h>
#include <nrf_log_default_backends.h>
#include "ADS1299_nRF.h"
#include "nrf_delay.h"
#include "nrf_gpio.h"

#define LED_PIN NRF_GPIO_PIN_MAP(0,13)  // LED1 on nRF52840 DK

int main(void) {
    NRF_LOG_INIT(NULL);
    NRF_LOG_DEFAULT_BACKENDS_INIT();

    nrf_gpio_cfg_output(LED_PIN);
    nrf_gpio_pin_clear(LED_PIN);

    NRF_LOG_INFO("Starting ADS1299 initialization");

    if (!ADS1299_init()) 
    {
        NRF_LOG_ERROR("ADS1299 init failed");
        while (1) {
            nrf_gpio_pin_toggle(LED_PIN);
            NRF_LOG_FLUSH();
            nrf_delay_ms(200);
        }
    }

    if(!ADS1299_send_sdatac())
    {
        NRF_LOG_INFO("ADS1299 SDATAC operation failed.");
    }
    else
    {
        NRF_LOG_INFO("SDATAC succesfully");
    }

    uint8_t id;
    ADS1299_read_register(ID,&id);
    if(id == 0x3E)
    {
        NRF_LOG_INFO("ADS1299 communication succes");
    }
    else
    {
        NRF_LOG_INFO("ADS1299 communication fail");
    }

}

  • 0 in reply to omerBzkrt

    Remove the MMB0 base board, power the ADS board from the DK directly.

    I don't remember if the MMB0 was neutral or not by default - but you want control to be entirely on the Nordic chip.

    The connectors should be on a 2.54mm raster - we used a prototyping board for our experimental setup that was hand soldered rather quickly. No, I don't have a schematic here.

  • 0 in reply to Turbo J

    Thanks for your quick reply  . Can it be that the problem with the MMBO board is not recognising the nRF chip as a master? Anyway, do you see any misconfiguration in the traces that I share?

    Hi   I have removed the MMBO baseboard and powered the ADS from the DK. However, I am getting the same result: the ADS is not responding. 

Reply Children
No Data
Related
Terms of service