Reconnect to bonded Smartphone

[danny0007]

Hi, 

nRF5340 and SDK v3.0.0 I'm using.

Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising and be invisible.

From smartphone side:  in case the smartphone is out of range or the bluetooth on smartphone is disabled

From BLE device side: or in case the bond information on the nRF5340 is removed.

Except rebooting the device, there is no way to make them connect to each other again. 

this is the BLE related funcitons:

	if (bt_conn_auth_cb_register(&conn_auth_callbacks)) {
		LOG_ERR("Failed to register authorization callbacks.\n");}

	if (bt_conn_auth_info_cb_register(&conn_auth_info_callbacks)) {
		LOG_ERR("Failed to register authorization info callbacks.\n");}

	bt_conn_cb_register(&connection_callbacks);

	if (bt_enable(NULL)) {
		LOG_ERR("Bluetooth init failed. \n");}

	if (IS_ENABLED(CONFIG_SETTINGS)) {
		settings_load();}

	if (bt_services_init(&app_callbacks)) {
		LOG_ERR("Failed to init LBS. \n");}

	LOG_INF("Bluetooth initialized\n");

	if (bt_le_adv_start(BT_LE_ADV_CONN_FAST_2, ad, ARRAY_SIZE(ad), sd, ARRAY_SIZE(sd))) {
		LOG_ERR("Advertising failed to start. \n");}

this is BLE related configurations:

# Button and LED library
CONFIG_BT_LBS=y
CONFIG_BT_LBS_POLL_BUTTON=y
CONFIG_DK_LIBRARY=y
CONFIG_BT_LBS_SECURITY_ENABLED=y

# Bluetooth LE
CONFIG_BT=y
CONFIG_BT_PERIPHERAL=y
CONFIG_BT_DEVICE_NAME="TEST_BLE"
CONFIG_BT_SMP=y
CONFIG_SETTINGS=y
CONFIG_BT_SETTINGS=y
#data length and MTU
CONFIG_BT_USER_DATA_LEN_UPDATE=y
CONFIG_BT_CTLR_DATA_LENGTH_MAX=251
CONFIG_BT_BUF_ACL_RX_SIZE=1024
CONFIG_BT_BUF_ACL_TX_SIZE=251
CONFIG_BT_L2CAP_TX_MTU=247
CONFIG_BT_GATT_CLIENT=y
CONFIG_BT_AUTO_PHY_UPDATE=n

**********************************************************************

What I want:

1. just like the earphone, if the connection is lost, they shall be able to reconnect to each other by themselves automatically.

2. if the bond info is removed on the device, it shall advertise and be visible again. 

How can I achive these? 

Regards

Danny

[Edvin]

Hello,

I am terribly sorry for the late reply. We are a bit low staffed, and we are working on holding the queue down. I am sorry for the inconvenience.

Except rebooting the device, there is no way to make them connect to each other again.

Do you mean rebooting, or re-programming the device?

Is it possible to upload the entire application? Mot relevant is the file with all of your Bluetooth implementation, where you set what sort of advertising to use when there is a bonded device, but in case I need to look at something else. That saves us one day of back and forth in case I need some other file.

Are you able to see this behavior on a DK, or does it require a custom board?

General: How do you want your peripheral device to behave? If it is connected and bonded to a central device, and then the central disconnects (possibly out of range for a short while). What do you want the peripheral to do? Only accept connections from the already bonded device?

When do you want it to start accepting new connections? On a button press? After a given amount of time?

Best regards,

Edvin

[danny0007]

Hi Edvin 

fully understandable, it's sommer, the most are in holiday:)

Anyway thanks a lot for the reply!

1. rebooting, I mean cycle the power, USB plug out, then plug in.

2. I don't think it's hardware related.

3. "General: How do you want your peripheral device to behave?"
good question: first, they are connected to each other, then the central(smartphone) is out of range, for a certain time, for instance 15 minutes, the peripheral and central shall try to reconnect to each other, after 15 minutes, stop the try.

yes, only accept connections from the alreay bonded device, as the earphone to smartphone.

"When do you want it to start accepting new connections? On a button press? After a given amount of time?"

No buttons on device, if it receives a int signal from the inertial sensor on board occasionally, it will try to start accepting new conncections again, or every 5 minutes there will be a try for reconncetion.

it's difficult to share the whole project code, just give me some hints, which functions or logic or documents shall I try, I can try it by myself.

Best regards

Danny