• State Verified Answer
  • Replies 6 replies
  • Subscribers 87 subscribers
  • Views 4237 views
  • Users 0 members are here
Attachments (1) Download All
Nordic Case Info
  • Case ID: 346806
Options

GPS 1PPS on nRF9151 DK

Yun531

Hello, my application requires very precise timing to trigger an action on the edge of the GPS time. I just need to get this time once in a while to synchronize the system, and afterwards, I can trigger a timer interrupt every 1s following the event of the GPS time trigger. After some time searching in the documentation, I found that the nRF9151 DK has a COEX1 interface, quoting from these 2 sources (source 1 and source 2):

COEX1 – Output from the LTE modem to the external device. When internal GPS is used, COEX1 delivers the GPS 1PPS (one pulse per second) time mark pulse. The 1PPS feature must not be used when LTE is enabled.

I'm trying to find a way to access GPS PPS signal, but unsure how. The closest forum post I found is this: https://devzone.nordicsemi.com/f/nordic-q-a/75137/getting-access-to-the-gps-pps-signal-on-the-nrf9160, but the question is about nRF9160 and it's over 2 years old, so I'm not sure if this is still relevant for the new nRF9151 DK. From this document, it seems that I can configure 1PPS, but I don't know how to get this. Is it via an interrupt? Do I need to make any hardware wiring? I'd appreciate it if there is a sample application or general guidance on how to approach it. Thank you.

Parents
  • 0

    Hello,

    it should be possible to enable this on the nrf9151. Check out this part of the documentation.

    1PPS can be accessed on the COEX1 pin on the nrf9151, P24 pin2 on the DK. You should read the details about the COEX interface. Also, importantly make sure that LTE is disabled during 1PPS operation on COEX1.

    I was unfortunately not able to find a proper sample for this.

  • 0 in reply to Hakon

    Hi,

    If there is no sample for using the COEX1, is there any sample or general guide on how to enable and disable LTE manually?

    I'm currently working through the Cellular IoT Fundamentals course and so far, the exercises for LTE and GNSS to be active at the same time is enable GNSS when the LTE is in power saving mode (Lesson 6 exercise 2). My SIM does not support PSM or eDRX, and here's a note from the lesson:

    If your network operator and/or SIM card does not support either PSM nor eDRX, you will have to manually deactivate and activate the modem when wanting to use the GNSS in your application. There is a workaround, by giving the GNSS priority over LTE events to help get a fix. This is not recommended, as it interferes with LTE operations.

    Could you help me with this? Especially, there is a "keep alive" while true loop in main, I'm unsure on how to manually deactivate/activate the modem in conjunction with this loop.

    If helpful, here are the links that I refered to:

    GNSS Lesson 6 Exercise

Reply
  • 0 in reply to Hakon

    Hi,

    If there is no sample for using the COEX1, is there any sample or general guide on how to enable and disable LTE manually?

    I'm currently working through the Cellular IoT Fundamentals course and so far, the exercises for LTE and GNSS to be active at the same time is enable GNSS when the LTE is in power saving mode (Lesson 6 exercise 2). My SIM does not support PSM or eDRX, and here's a note from the lesson:

    If your network operator and/or SIM card does not support either PSM nor eDRX, you will have to manually deactivate and activate the modem when wanting to use the GNSS in your application. There is a workaround, by giving the GNSS priority over LTE events to help get a fix. This is not recommended, as it interferes with LTE operations.

    Could you help me with this? Especially, there is a "keep alive" while true loop in main, I'm unsure on how to manually deactivate/activate the modem in conjunction with this loop.

    If helpful, here are the links that I refered to:

    GNSS Lesson 6 Exercise

Children
No Data
Related
Terms of service