nPM1300 does not exit ship hold mode when SHPHLD button pressed or VBUS connected

[joelspadin]

Hello,

I have custom hardware using an nPM1300 and nRF52840, and I am having trouble getting the nPM1300 to work as described in its documentation. I have a button connected between the SHPHLD pin and ground, and I can tell it is working because I get GPIO events, and a long press does reset the nPM1300. However, if I enable ship hold mode, then it does not exit ship hold mode with either a short press of the button or plugging in USB. I can only get it to exit with a long press.

You can see my hardware at kicanvas.org/?github=https%3A%2F%2Fgithub.com%2Fjoelspadin%2Fmarten_numpad%2Fblob%2Fmain%2Fpcb%2Fnumpad.kicad_pro. The relevant schematics are in usb.kicad_sch and numpad.kicad_sch.

I am using Zephyr 4.1. My devicetree setup for the nPM1300 looks like this:

&i2c0 {
    compatible = "nordic,nrf-twi";
    status = "okay";

    pinctrl-0 = <&i2c0_default>;
    pinctrl-1 = <&i2c0_sleep>;
    pinctrl-names = "default", "sleep";

    npm1300_pmic: pmic@6b {
        compatible = "nordic,npm1300";
        status = "okay";
        reg = <0x6b>;

        host-int-gpios = <&gpio0 30 0>;
        pmic-int-pin = <1>;
        long-press-reset = "one-button";

        npm1300_regulators: regulators {
            compatible = "nordic,npm1300-regulator";

            main_regulator: BUCK2 {
                regulator-min-microvolt = <3300000>;
                regulator-max-microvolt = <3300000>;
                regulator-always-on;
            };
        };

        npm1300_charger: charger {
            compatible = "nordic,npm1300-charger";
            charging-enable;

            term-microvolt = <4150000>;
            term-warm-microvolt = <4000000>;
            current-microamp = <250000>;
            dischg-limit-microamp = <1000000>;
            vbus-limit-microamp = <500000>;

            // No thermistor
            thermistor-ohms = <0>;
            thermistor-beta = <3380>;
        };

        npm1300_leds: leds {
            compatible = "nordic,npm1300-led";
            nordic,led0-mode = "charging";
            nordic,led1-mode = "host";
            nordic,led2-mode = "host";
        };
    };
};

Using

    static struct gpio_callback event_cb;
    gpio_init_callback(&event_cb, power_button_callback, BIT(NPM1300_EVENT_SHIPHOLD_PRESS));
    mfd_npm1300_add_callback(pmic, &event_cb);

I have set up a callback which checks if USB is powered. If not, it blinks an LED a few times, then calls regulator_parent_ship_mode(). With the board powered only from a battery, when I press the button, the LED blinks, then it shuts off and the voltage to the SoC drops to 0 as expected. When I press the button again, nothing happens. (I can tell it is not waking, immediately triggering the GPIO event, and then going back into ship mode, because the LED does not blink.) Similarly, reconnecting USB power does not wake it either.

Is there something else I'm missing that needs to be configured?

[Tomi Koskela]

Hello,

Is this behavior seen in multiple devices, or with just a single device? Just to check is this systematic issue and not a damaged PMIC or soldering problem for example.  

Code itself seems to be ok, no issues seen with it. 

Also the schematic looks ok.

nPM1300 should wakeup when VBUS is present, so something seems to be off here. Have you measured VBAT and VBUS in this condition? What is the measured voltage at SHPHLD?

Does the nPM1300 charge the battery and buck starts with correct voltage?

[joelspadin]

On this one board:

Voltage	Ship mode	Ship mode	Normal mode	Normal mode
	USB connected	USB disconnected	USB connected	USB disconnected
VBUS	4.9 V	0 V	4.9 V	0 V
VBAT	4.13 V	4.0 V	4.13 V	4.0 V
SHPHLD (at switch)	4.9 V	-30 mV	4.9 V	4.0 V
BUCK2 output	2 mV	9 mV	3.2 V	3.2 V
Charge LED	Off	Off	On	Off

Everything looks correct to me when not in ship mode, and all the voltages look correct when in ship mode with USB connected (it even looks like it is charging the battery despite the charge LED being off), however SHPHLD doesn't seem to be getting pulled up to the battery voltage when in ship mode and USB is disconnected.

I do have a few more boards. I can check if they behave the same way sometime later.