How to use the 2.4G to simulate send Advertising packet with non-connectable and non-scannable with nrf52832

[freeman_shanghai]

I want to send Advertising packet with non-connectable and non-scannable via 2.4G without using the Bluetooth protocol stack. I try Congfig Nrf52832 's RADIO ,but it didn't work.

unsigned char broadcast_data[] = 
{
	0x02,17,
	0x01,0x02,0x03,0x04,0x05,0x06,//mac
	0x02,0x01,0x05,
	0x07,0x08,'H', 'e', 'l', 'l', 'o','Y',
};

__STATIC_INLINE void nrf_radio_config_as_advertisement(unsigned char ch)
{
	
	// Radio config
    NRF_RADIO->TXPOWER   = (NRF_RADIO_TXPOWER_0dBm << RADIO_TXPOWER_TXPOWER_Pos);
    NRF_RADIO->FREQUENCY = ch == 37 ? 2 : (ch == 38 ? 26 : 80);
    NRF_RADIO->MODE      = (RADIO_MODE_MODE_Ble_1Mbit << RADIO_MODE_MODE_Pos);

#if 1

	NRF_RADIO->PCNF0 =  (RADIO_PCNF0_S0LEN_1BYTE << RADIO_PCNF0_S0LEN_Pos) |
						(RADIO_PCNF0_S1LEN_0bit << RADIO_PCNF0_S1LEN_Pos) |
						(RADIO_PCNF0_LFLEN_8bit << RADIO_PCNF0_LFLEN_Pos) ;
	
	
	NRF_RADIO->PCNF1 =  (RADIO_PCNF1_WHITEEN_Disabled    << RADIO_PCNF1_WHITEEN_Pos) |
						(RADIO_PCNF1_ENDIAN_Little       << RADIO_PCNF1_ENDIAN_Pos)  |
						(3                               << RADIO_PCNF1_BALEN_Pos)   |
						(0                               << RADIO_PCNF1_STATLEN_Pos) |
						(37                              << RADIO_PCNF1_MAXLEN_Pos);  
#else
    
	
	NRF_RADIO->PCNF0 =  (0 << RADIO_PCNF0_S0LEN_Pos) |
						(0 << RADIO_PCNF0_S1LEN_Pos) |
						(0 << RADIO_PCNF0_LFLEN_Pos) ;
	
	
	NRF_RADIO->PCNF1 =  (RADIO_PCNF1_WHITEEN_Disabled    << RADIO_PCNF1_WHITEEN_Pos) |
						(RADIO_PCNF1_ENDIAN_Little       << RADIO_PCNF1_ENDIAN_Pos)  |
						(3                               << RADIO_PCNF1_BALEN_Pos)   |
						(19                              << RADIO_PCNF1_STATLEN_Pos) |
						(19                              << RADIO_PCNF1_MAXLEN_Pos);  
#endif
	
	NRF_RADIO->DATAWHITEIV = ch|0x40;
	NRF_RADIO->PCNF1 |= RADIO_PCNF1_WHITEEN_Enabled << RADIO_PCNF1_WHITEEN_Pos;
	
	
    NRF_RADIO->BASE0 = 0x8E89BED6;
    NRF_RADIO->PREFIX0 = 0x8E8E8E8E; 
	
	NRF_RADIO->BASE1 = 0x8E89BED6;
    NRF_RADIO->PREFIX1 = 0x8E8E8E8E; 
	
	NRF_RADIO->TXADDRESS   = 0x00UL;
	
	
    NRF_RADIO->CRCCNF =(RADIO_CRCCNF_LEN_Three << RADIO_CRCCNF_LEN_Pos |RADIO_CRCCNF_SKIPADDR_Skip << RADIO_CRCCNF_SKIPADDR_Pos);
    
	NRF_RADIO->CRCINIT = 0x555555UL; 
    NRF_RADIO->CRCPOLY = 0x0100065B; 
	
	
}

[Sigurd]

Hi!

without using the Bluetooth protocol stack.

Why? I strongly recommend using the Bluetooth stack for this.

[freeman_shanghai]

Since the Bluetooth protocol stack occupies flash memory and RAM, and also increases programming time, and given that I only need to send broadcast packets at regular intervals (similar to how 2.4G works) without using any other Bluetooth functions, I don’t think it’s necessary to use the protocol stack.

[Sigurd]

Hi,

The BLE protocol has strict timing and formatting rules, and using the Bluetooth stack guarantees BLE compliance, with robust and reliable behavior. The nRF52832 has 512 KB flash, and e.g. the S112 stack will take around 100KB, so you still have 80% of the flash to your application.