app_time and nrf_delay_ms

[samo]

Hi

I would like to read values from three AD channels where I use different sampling frequencies and different number of samples are captured at each sampling frequency. To be clear I will explain my problem in the case of one channel. Every 10s I would like to capture five values from the actual channel and subsequently the averaging is performed. The time between each sample should be around 10ms. At this stage I do not know what is the best programming solution for my problem to be the sofware as efficient as possible. Here is my current code, where I used nrf_delay_ms(10) function for waiting between two samples. I know that this is not the most efficient way because of that I will appreciate for any advice how I can improve my code.

Best regards

Samo

static void adc_lpg_timer_handler(void * p_context) // timer executed every 10s
{ 	
	
	int i;
	nrf_adc_value_t adc_value;
	uint8_t err_code;
	uint16_t ave_adc = 0;
	
	nrf_gpio_pin_toggle(LPG_PIN);	
	
	for(i=0; i < 5; i++)
	{
		nrf_delay_ms(10);
		while(nrf_drv_adc_is_busy())
		{
		}	
		err_code = nrf_drv_adc_sample_convert(&adc_lpg,&adc_value);
		APP_ERROR_CHECK(err_code);
	
	  ave_adc = ave_adc + adc_value;
  }
	 ave_adc = ave_adc/5;
	 ave_adc = 1200*ave_adc/1023;	 	 	
	 err_code = ble_adcs_2_update(&m_adcs,ave_adc);	 
	 APP_ERROR_CHECK(err_code);
	 ave_adc = 0;	   		
	 
	 nrf_gpio_pin_toggle(LPG_PIN);	
}

[samo]

Hi Øyvind,

thanks for fast reply. Do you have in mind the following idea? What is better solution to using one timer (such as presented in my code) or two timers, where the first timer which is triggered every 10s enables the second timers which has frequency 1/10ms. The latter one is executed 5 times to get 5 samples from ADC.

Thanks for answer in advance.

Best regards

Samo

static void experimental_timer_handler(void * p_context)
{	
	uint8_t err_code;
	
	static int counter = 0;
	
	counter++;	
	
	if(counter == 1)
	{
	app_timer_stop(m_experimental_timer_id);	
	err_code = app_timer_start(m_experimental_timer_id, APP_TIMER_TICKS(10, APP_TIMER_PRESCALER),NULL);
	}	
	else if (counter > 1 && counter <= 6)
	{
	 // ad sampling five times
	}
	else // counter > 6
	{
		app_timer_stop(m_experimental_timer_id);	
	  err_code = app_timer_start(m_experimental_timer_id, APP_TIMER_TICKS(10000, APP_TIMER_PRESCALER),NULL);
		counter = 0;
	}
}

[Øyvind Karlsen]

The events generated by the capture compare (CC) register in the real time counter (RTC) module, which uses the low frequency clock, will allow you to trigger tasks via PPI.

[Vijay]

Hi Oyvind, I know this is a very old thread but I have a question that pertains to this concept.

I have a TWI sensor that does four operations and there is a 20 ms time delay as mandated by the sensor datasheet. 

I have gotten the code working using the nrf_delay_ms(20) function but I have since realized that it's not power efficient. So, after perusing through the forum I have decided to implement the delay using Application timers after following the tutorial. 

My main function is,

    int main(void){
    lfclk_request();
    
    APP_TIMER_INIT(0, 4, false);
    
    gpio_config();
    
    nrf_drv_gpiote_out_clear(LED_1_PIN);

    err_code = app_timer_start(m_led_b_timer_id, APP_TIMER_TICKS(2000, 0), NULL);
    APP_ERROR_CHECK(err_code);
    
    nrf_drv_gpiote_out_set(LED_1_PIN);
    }

The LED_1_PIN is the LED 1 on the Devkit. 'm_led_b_timer_id' is a single shot timer. The timer handler has nothing but a UNUSED_PARAMETER command. I am using nRF52832 with a s132 softdevice and SDK v12.2

This doesn't give me a 2 s time delay. DO you know where I am going wrong?

Thanks,

Vijay