Wake on motion in nrf52

[Swapnil]

Hello,

I am trying to implement wake on motion functionality of MPU9250 with nRF52. I am writing below sequence code for wake on motion configuration:

void MPU6500_StartMotionDetection(void) { uint8_t val; uint32_t err_code;

// Make sure accelerometer is running
val = 0x09;
i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_PWR_MGMT_1, 0x09);

// Enable accelerometer, disable gyro
val = 0x07;
i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_PWR_MGMT_2, 0x07);

// Set Accel LPF setting to 184 Hz Bandwidth
val = 0x01;
i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_ACCEL_CONFIG_2, 0x01);

// Enable Motion Interrupt
val = 0x40;
i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_INT_ENABLE, 0x40);

// Enable Accel Hardware Intelligence
val = 0xC0;
i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_MOT_DETECT_CTRL, 0xC0);

// Set Motion Threshold
i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_WOM_THR, 0x06);

// Set Frequency of Wake-up

i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_LP_ACCEL_ODR, 6);

// Enable Cycle Mode (Accel Low Power Mode)
val = 0x29;
i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_PWR_MGMT_1, 0x29);

// Clear interrupt
i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_INT_STATUS, 0x29);

printf("%s: MPU6500_StartMotionDetection\r\n", print_timestamp());

}

and I am calling it inside mpu initialization after mpu_int_cfg_pin() function. Before that I am setting gpio config as shown below:

static void gpio_init(void) { ret_code_t err_code;

err_code = nrf_drv_gpiote_init();
printf("%s: nrf_drv_gpiote_init_err_code: %lu\r\n", print_timestamp(), err_code);
APP_ERROR_CHECK(err_code);

nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_LOTOHI(true);

err_code = nrf_drv_gpiote_in_init(MPU9250_INT_PIN, &in_config, int_pin_handler);
printf("%s: nrf_drv_gpiote_in_init_err_code: %lu\r\n", print_timestamp(), err_code);
APP_ERROR_CHECK(err_code);

nrf_drv_gpiote_in_event_enable(MPU9250_INT_PIN, true);

}

But I am getting error in it.

Is it the proper way for configuring ?

[Swapnil]

Sorry for confusion but I changed it and I am using below configuration

uint32_t MPU6500_StartMotionDetection(void)

{

uint32_t err_code[CONFIGURATION_CHECK_LENGTH];


//*********************************************************************************//
// Make sure accelerometer is running
//In PWR_MGMT_1 (0x6B) make CYCLE = 0, SLEEP = 0 and STANDBY = 0
err_code[0] = i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_PWR_MGMT_1, 0x00);

//Set DIS_XA, DIS_YA, DIS_ZA = 0 and DIS_XG, DIS_YG, DIS_ZG = 1
err_code[1] = i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_PWR_MGMT_2, 0x07);

// Set Accel LPF setting to 184 Hz Bandwidth
//ACCEL_CONFIG 2 (0x1D) set ACCEL_FCHOICE_B = 1 and A_DLPFCFG[2:]=1(b001)
err_code[2] = i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_ACCEL_CONFIG_2, 0x05);

// Enable Motion Interrupt
err_code[3] = i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_INT_ENABLE, 0x40);

// Enable Accel Hardware Intelligence
//In MOT_DETECT_CTRL (0x69), set ACCEL_INTEL_EN = 1 and ACCEL_INTEL_MODE = 1
err_code[4] = i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_MOT_DETECT_CTRL, 0xC0);

// Set Motion Threshold
//In WOM_THR (0x1F), set the WOM_Threshold[7:0] to 1~255 LSBs (0~1020mg)
err_code[5] = i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_WOM_THR, 0xFF);

// Set Frequency of Wake-up
//In LP_ACCEL_ODR (0x1E), set Lposc_clksel[3:0] = 0.24Hz ~ 500Hz
err_code[6] = i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_LP_ACCEL_ODR, 0x03);

// Enable Cycle Mode (Accel Low Power Mode)
//In PWR_MGMT_1 (0x6B) make CYCLE =1
err_code[7] = i2c_write_registers(I2C_MPU9250_ADDR, MPU_REG_PWR_MGMT_1, 0x03);
//*********************************************************************************//

}