eclipse include path added, but still can't find nrf_error.h?

[julian]

I am able to use eclipse to run simple project, but after move the real one, getting lost of errors:

www.dropbox.com/.../Screenshot 2014-04-02 09.10.41.png

I add required include path include/s110, but still complain can't find it,

any helps are appreciated

[julian]

Thanks www.dropbox.com/.../Screenshot 2014-04-10 14.46.32.png I was able to check one more do not use default libraries however, still get RAM error, and it is complaining when I set Heap to 100,

without it, it is ok to build by heap 100 and stack 1024, while keil is ok to be both 1024

checking other two options will results can't find _start www.dropbox.com/.../Screenshot 2014-04-10 14.49.17.png

[Nguyen Hoan Hoang]

You need to remove gcc_startup and your sections.ld if you want to use mine but not both at same time.

[julian]

very strange, I can only comment, can't reply, reply will not show up

[julian]

after I set back to windows, and switch back, the debugger works now

SWO disabled succesfully. ERROR: Could not detect CPU clock speed. Verification of test code downloaded into RAM failed.

Failed to enable SWO. Could not measure target CPU frequency. Read 4 bytes @ address 0x00012B98 (Data = 0x681B4B15) Downloading 16192 bytes @ address 0x00014000 - Verify failed Downloading 15968 bytes @ address 0x00017F40 - Verify failed Downloading 16160 bytes @ address 0x0001BDA0 - Verify failed Downloading 16096 bytes @ address 0x0001FCC0 - Verify failed Downloading 16080 bytes @ address 0x00023BA0 - Verify failed Downloading 16176 bytes @ address 0x00027A70 - Verify failed Downloading 12208 bytes @ address 0x0002B9A0 - Verify failed Downloading 68 bytes @ address 0x0002E950 - Verify failed Downloading 8 bytes @ address 0x0002E994 - Verify failed Downloading 2396 bytes @ address 0x0002E99C - Verify failed Writing register (PC = 0x0002e951) Read 4 bytes @ address 0x0002E950 (Data = 0xFFFFFFFF) Read 4 bytes @ address 0xFFFFFFFF (Data = 0x001C4800) Read 4 bytes @ address 0xFFFFFFFF (Data = 0x001C4800) Resetting target Halting target CPU... ...Target halted (PC = 0x00012B98) R0 = FFFFFFFF, R1 = FFFFFFFF, R2 = FFFFFFFF, R3 = FFFFFFFF R4 = FFFFFFFF, R5 = FFFFFFFF, R6 = FFFFFFFF, R7 = FFFFFFFF R8 = FFFFFFFF, R9 = FFFFFFFF, R10= FFFFFFFF, R11= FFFFFFFF R12= FFFFFFFF, R13= 20001C48, MSP= 20001C48, PSP= FFFFFFFC R14(LR) = FFFFFFFF, R15(PC) = 00012B98 XPSR C1000000, APSR C0000000, EPSR 01000000, IPSR 00000000 CFBP 00000000, CONTROL 00, FAULTMASK 00, BASEPRI 00, PRIMASK 00 Reading all registers Read 4 bytes @ address 0x00012B98 (Data = 0x681B4B15) Starting target CPU... Debugger requested to halt target... ...Target halted (PC = 0x0000FE3E) Reading all registers Read 4 bytes @ address 0x0000FE3E (Data = 0xBF20BF40) Read 4 bytes @ address 0x0000016A (Data = 0x9801B401) Read 4 bytes @ address 0x0000016A (Data = 0x9801B401)

however, it can't stop at any break point, the board seems ok to run, just can't stop https://www.dropbox.com/s/v1xe3gvz8hm1w9t/Screenshot%202014-04-10%2017.08.08.png