Hi Nordic community, I'm sending several packets from nrf51822 (custom board) to Android application. At the moment I want to configure the sensor by sending commands from android to nrf51822. I have a difficulty in how to receive the command over ble and send it to uart and handle. any recommendation is appreciated. please, the code for sending the data are attached. Best regards, Mostafa
void initAll()
{
initMCU();
Leds_init();
Leds_setColor(1, 1, 1);
Twiface_init();
#if 0
Twiface_scanForDevices(
MCU_I2C_SDA, MCU_I2C_SCL, TWI_FREQUENCY_FREQUENCY_K100);
Twiface_scanForDevices(
MCU_BRD_RTS_I2C2_SDA, MCU_BRD_CTS_I2C2_SCL, TWI_FREQUENCY_FREQUENCY_K100);
#endif
initNrfSwModules();
#if 1
Sensors_init();
initExtmem();
//Datalog_init();
Sampler_init();
#endif
Ble_control_init(); (service is initiliazed here)
//Rtc_init();
ssd1306_init();
////////////////////////////////
void Ble_control_init(void)
{
ble_stack_init();
device_manager_init(true);
gap_params_init();
advertising_init();
initBatteryService();
initDeviceInformationService();
initDFUService();
nus_services_init();
conn_params_init();
// Start execution.
// Initialize advertising parameters (used when starting advertising).
memset(&m_adv_params, 0, sizeof(m_adv_params));
m_adv_params.type = BLE_GAP_ADV_TYPE_ADV_IND;
m_adv_params.p_peer_addr = NULL; // Undirected advertisement.
m_adv_params.fp = BLE_GAP_ADV_FP_ANY;
m_adv_params.interval = APP_ADV_INTERVAL;
m_adv_params.timeout = APP_ADV_TIMEOUT_IN_SECONDS;
advertising_start();
//err_code = sd_ble_gap_adv_start(&m_adv_params);
//err_code = ble_advertising_start(BLE_ADV_MODE_FAST);
//APP_ERROR_CHECK(err_code);
}
/////////////////////////////////////
void readNoise(bool isConnected)
{
AistinItem ai;
nrf_delay_ms(10);
memset(withSizeof(ai.data._B750.noise), 0x00);
Aistin_initItem(&ai, AISTIN_ID_B750_NOISE);
sound_sensor_adc_start();
ai.data._B750.noise[1] = soundLevel & 0xFF;
ai.data._B750.noise[0] = (soundLevel >> 8) & 0xFF;
ai.dataSize = sizeof(ai.data._B750);
if (isConnected) Protocol_sendBle(&ai);
////////////////////////////////////////////
void sendBle(uint8_t *data, int dataSize, uint16_t maxTimeToTry)
{
int tries = 0;
int32_t err;
uint16_t start = Timing_read32768Hz16();
uint16_t elapsed;
do {
tries++;
err = ble_nus_string_send(&m_nus, data, dataSize);
if (err == NRF_SUCCESS) break;
elapsed = Timing_read32768Hz16() - start;
sd_app_evt_wait();
} while (elapsed < maxTimeToTry);
if (err != NRF_SUCCESS) {
debugf("%d", tries);
}
else {
if (tries > 1) debug(":");
}
}
//////////////////////////////////
void nus_data_handler(ble_nus_t * p_nus, uint8_t * p_data, uint16_t length)
{
debugln(__func__);
Protocol_handleMessage(p_data, length);
}
///////////////////////////////////////
void Protocol_handleMessage(uint8_t *msg, uint16_t len)
{
if (len >= sizeof(AistinCommand) - 1) {
debugln("*** cmd!");
AistinCommand *ac = (AistinCommand*)msg;
uint16_t id16 = (ac->dataID[0]<<8) | ac->dataID[1];
if (id16 == AISTIN_ID_8607_LOGGER_CONFIG) {
debuglnf("- log: %d", ac->data[0]);
if (!(ac->data[0] & _AISTIN_8607bit__LOG) && Datalog_isLogging())
Datalog_stopLogging();
else
if ((ac->data[0] & _AISTIN_8607bit__LOG) && !Datalog_isLogging())
Datalog_startNewLog();
}
}
}
//////////////////
this is the code related to send sensor data and working well
