High power consumption of softdevice

Question

Hello! 
 I am working on firmware for device that has freertos in the base and implements BLE beacon and 1 service with 7 characteristics. Everything works. But power consumption is too high. 
 After plenty of tests on final HW, I've created playground based on ble_app_hrs_freertos_pca10040_s132 sample project and switched to sparkfun board. 
 When have just FreeRTOS with no user-defined tasks, consumption is about 1uA. 
 After I call ble_stack_init with code below, I got about 500uA. It is without advertising at all. 
 static void ble_stack_init(void)
{
 ret_code_t err_code;

 err_code = nrf_sdh_enable_request();
 APP_ERROR_CHECK(err_code);

 // Configure the BLE stack using the default settings.
 // Fetch the start address of the application RAM.
 uint32_t ram_start = 0;
 err_code = nrf_sdh_ble_default_cfg_set(APP_BLE_CONN_CFG_TAG, &ram_start);
 APP_ERROR_CHECK(err_code);

 // Enable BLE stack.
 err_code = nrf_sdh_ble_enable(&ram_start);
 APP_ERROR_CHECK(err_code);

 // Register a handler for BLE events.
 NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);
} 
 When beacon is enabled I have cca 650uA. 
 When GATT and beacon are working I have cca 750uA. 
 I measure with multimeter. 
 Results seems fine for me except for those 500uA after stack is initialized. Why is it so high? What can I do to lower it? 
 
 SDK v 15.0 
 NRF_LOG_ENABLED is 0 
 Using RELEASE configuration. 
 Tried S132 and S140 - result is the same

Elias Löwe · Accepted Answer

Hi David! I can confirm, that Aryan's answer worked for me. I just changed #if 0 to #if 1 # file port_cmsis_systick.c #if 1 // With FreeRTOS sd_app_evt_wait increases power consumption with FreeRTOS compared to _WFE (NRFFOSDK-11174) #ifdef SOFTDEVICE_PRESENT if (nrf_sdh_is_enabled()) { uint32_t err_code = sd_app_evt_wait(); APP_ERROR_CHECK(err_code); } else #endif #endif // (NRFFOSDK-11174) This did its job for demo project. Also for this project I had to do few more things: 1. As far as I used floating point calculations, I had to chnage my main.c module as follows: int main(void) { NVIC_SetPriority(FPU_IRQn, APP_IRQ_PRIORITY_LOW); NVIC_EnableIRQ(FPU_IRQn); /* application code */ ... } #define FPU_EXCEPTION_MASK 0x0000009F void FPU_IRQHandler(void) { uint32_t *fpscr = (uint32_t *)(FPU->FPCAR+0x40); (void)__get_FPSCR(); *fpscr = *fpscr & ~(FPU_EXCEPTION_MASK); } 2. We use SAADC module for some measurements and I had to uninitialise it after usage like this after each usage: nrf_drv_saadc_uninit(); NRF_SAADC->INTENCLR = (SAADC_INTENCLR_END_Clear << SAADC_INTENCLR_END_Pos); NVIC_ClearPendingIRQ(SAADC_IRQn); And now average power consumption is about 30uA. p.S. Sorry for late answer, so much work here...

Susheel Nuguru · Answer

I think i found the problem. 
 It is in port_cmsis_systick.c 
 #if 0 // With FreeRTOS sd_app_evt_wait increases power consumption with FreeRTOS compared to _WFE (NRFFOSDK-11174)
#ifdef SOFTDEVICE_PRESENT
 if (nrf_sdh_is_enabled())
 {
 uint32_t err_code = sd_app_evt_wait();
 APP_ERROR_CHECK(err_code);
 }
 else
#endif
#endif // (NRFFOSDK-11174) 
 I do not remember the exact way i came to a conclusion that sd_app_evt_wait was consuming more power with freertos. Hence I created an internal ticket NRFFOSDK-11174 to investigate why this happened. I remembered that i was reading more power with freertos and using sd_wait function. While using WFI it was less. This technically did not make sense, but i decided to comment out sd_app_evt_wait function until i get more results. But I am not able to reproduce this anymore. So i think this comment is the problem on SDK 15. 
 Please change line 231 in port_cmsis_systick.c to below 
 #ifdef SOFTDEVICE_PRESENT
 if (nrf_sdh_is_enabled())
 {
 uint32_t err_code = sd_app_evt_wait();
 APP_ERROR_CHECK(err_code);
 }
 else
#endif
 
 I will try to push these changes to official SDK for the next release.

Elias Löwe · Answer

Hi Rahmat, 
 yes, make sure that UART and logging is switched off in your sdk_config.h and that you are not running your application with debugger. 
 Maybe some more information about your application could help to point you. 
 
 Cheers, 
 Elias

High power consumption of softdevice

Top Replies