• State Verified Answer
  • Locked Locked
  • Replies 15 replies
  • Subscribers 63 subscribers
  • Views 5923 views
  • Users 0 members are here
Attachments (0)
Nordic Case Info
  • Case ID: 103905
Options
This post is older than 2 years and might not be relevant anymore
More Info: Consider searching for newer posts
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Issues with DFU for SD v7

Anne

Hey!

I'm testing out the new SoftDevice and am trying to update firmware OTA but thus far have not been able to do so. I've tried from the Master Control Panel android app (v 2.0.2). I can discover and connect to DfuTarg no problem but when I try to actually update the firmware it gets to 0%, hangs there for maybe 5 seconds, and then disconnects. I also tried from the PC version of Master Control Panel (v3.7.0) and the same thing happened. It connected, discovered, started DFU, and hung at zero.

The SoftDevice is version 7.0.0 flashed from nRFgo Studio (v 1.17.0.3211), the bootloader is the version from SDK v6.1.0, and the firmware I'm trying to upload is the heart rate sensor app from the same SDK. This app works fine when flashed via nRFgo Studio.

I'm using a custom board and so have modified SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, true) in ble_stack_init() to be SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, false).

Thanks for your help ^^

Parents
  • 0

    Hi

    I've found the same error. My configuration is as follows:

    • SDK 6.1.0.0 using ble_app_hrs_dfu project without any change.
    • s110_nrf51822_7.0.0_softdevice.hex
    • nRFgoStudio 1.17.0
    • MCP 3.6.0

    I have used the following documentation:

    devzone.nordicsemi.com/.../a00076.html

    On the step 6, I click back but I can only see the device advertising again as 'Nordic_HRM'. I couldn't find the string "DfuTarg" searching files on the current project.

    Debugging I could see that the code is calling the bootloader_start function.

    Any other suggestion to test on my side?

    I have also tried the dfu with the nRF Toolbox from a nexus 4 and iphone 5 without any luck.

    Thanks.

    Screen Captures

    Before flashing the bootloader After flashing the bootloader

  • 0 in reply to Ignacio Lopez

    Hi Asbjørn

    Thank you for your quick reply. I have the following error trying to flash the bootloader hex

    Program Size: Code=14180 RO-data=328 RW-data=256 ZI-data=5988
    FromELF: creating hex file... "._build\bootloader.axf" - 0 Error(s), 0 Warning(s). *** Completed Cross-Module-Optimization after 3 iteration(s). "nrfjprog.exe" --reset --program "C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310\device_firmware_updates\bootloader\arm_build\bootloader.HEX" Parsing hex file(s). ERROR: Hex file(s) contain addresses outside the code, RAM and UICR areas.

    I am using a 128kb version of the chip

Reply
  • 0 in reply to Ignacio Lopez

    Hi Asbjørn

    Thank you for your quick reply. I have the following error trying to flash the bootloader hex

    Program Size: Code=14180 RO-data=328 RW-data=256 ZI-data=5988
    FromELF: creating hex file... "._build\bootloader.axf" - 0 Error(s), 0 Warning(s). *** Completed Cross-Module-Optimization after 3 iteration(s). "nrfjprog.exe" --reset --program "C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310\device_firmware_updates\bootloader\arm_build\bootloader.HEX" Parsing hex file(s). ERROR: Hex file(s) contain addresses outside the code, RAM and UICR areas.

    I am using a 128kb version of the chip

Children
No Data
Related