Question about current in low power mode.

[psj]

Hi
softdevice uses s130
The board is using nrf51 dk. The example uses the ble_app_beacon example from sdk12.3.
   if (switch_hit ())
         {
           // NRF_POWER-> SYSTEMOFF = 1;
         // sd_power_system_off ();
          
         sd_ble_gap_adv_stop ();
          power_manage ();
     
         }
I measured the current by adding this part. I normally use 4.5mA, and when I enter the low power mode, it consumes 0.9mA. I thought I would spend much lower. Is this correct? Or am I making a mistake?

For reference, when I tested with system_on_wakeup_on_gpio example in GITHUB, I consumed 20uA when entering sleep mode.
I need your help.

[Turbo J]

Show us more code. Some peripherials will keep HFCLK or HFINT running - this includes the debugger.

[psj]

#include <stdbool.h>
#include <stdint.h>
#include "ble_advdata.h"
#include "nordic_common.h"
#include "softdevice_handler.h"
#include "bsp.h"
#include "app_timer.h"
#include "nrf_log.h"
#include "nrf_log_ctrl.h"
#include "nrf_drv_gpiote.h"

#define CENTRAL_LINK_COUNT 0 /**< Number of central links used by the application. When changing this number remember to adjust the RAM settings*/
#define PERIPHERAL_LINK_COUNT 0 /**< Number of peripheral links used by the application. When changing this number remember to adjust the RAM settings*/

#define IS_SRVC_CHANGED_CHARACT_PRESENT 0 /**< Include or not the service_changed characteristic. if not enabled, the server's database cannot be changed for the lifetime of the device*/

#define APP_CFG_NON_CONN_ADV_TIMEOUT 0 /**< Time for which the device must be advertising in non-connectable mode (in seconds). 0 disables timeout. */
#define NON_CONNECTABLE_ADV_INTERVAL MSEC_TO_UNITS(100, UNIT_0_625_MS) /**< The advertising interval for non-connectable advertisement (100 ms). This value can vary between 100ms to 10.24s). */

#define APP_BEACON_INFO_LENGTH 0x17 /**< Total length of information advertised by the Beacon. */
#define APP_ADV_DATA_LENGTH 0x15 /**< Length of manufacturer specific data in the advertisement. */
#define APP_DEVICE_TYPE 0x02 /**< 0x02 refers to Beacon. */
#define APP_MEASURED_RSSI 0xC3 /**< The Beacon's measured RSSI at 1 meter distance in dBm. */
#define APP_COMPANY_IDENTIFIER 0x0059 /**< Company identifier for Nordic Semiconductor ASA. as per www.bluetooth.org. */
#define APP_MAJOR_VALUE 0x01, 0x02 /**< Major value used to identify Beacons. */
#define APP_MINOR_VALUE 0x03, 0x04 /**< Minor value used to identify Beacons. */
#define APP_BEACON_UUID 0x01, 0x12, 0x23, 0x34, \
0x45, 0x56, 0x67, 0x78, \
0x89, 0x9a, 0xab, 0xbc, \
0xcd, 0xde, 0xef, 0xf0 /**< Proprietary UUID for Beacon. */

#define DEAD_BEEF 0xDEADBEEF /**< Value used as error code on stack dump, can be used to identify stack location on stack unwind. */

#define APP_TIMER_PRESCALER 0 /**< Value of the RTC1 PRESCALER register. */
#define APP_TIMER_OP_QUEUE_SIZE 4 /**< Size of timer operation queues. */

#if defined(USE_UICR_FOR_MAJ_MIN_VALUES)
#define MAJ_VAL_OFFSET_IN_BEACON_INFO 18 /**< Position of the MSB of the Major Value in m_beacon_info array. */
#define UICR_ADDRESS 0x10001080 /**< Address of the UICR register used by this example. The major and minor versions to be encoded into the advertising data will be picked up from this location. */
#endif

static ble_gap_adv_params_t m_adv_params; /**< Parameters to be passed to the stack when starting advertising. */
static uint8_t m_beacon_info[APP_BEACON_INFO_LENGTH] = /**< Information advertised by the Beacon. */
{
APP_DEVICE_TYPE, // Manufacturer specific information. Specifies the device type in this
// implementation.
APP_ADV_DATA_LENGTH, // Manufacturer specific information. Specifies the length of the
// manufacturer specific data in this implementation.
APP_BEACON_UUID, // 128 bit UUID value.
APP_MAJOR_VALUE, // Major arbitrary value that can be used to distinguish between Beacons.
APP_MINOR_VALUE, // Minor arbitrary value that can be used to distinguish between Beacons.
APP_MEASURED_RSSI // Manufacturer specific information. The Beacon's measured TX power in
// this implementation.
};

/**@brief Callback function for asserts in the SoftDevice.
*
* @details This function will be called in case of an assert in the SoftDevice.
*
* @warning This handler is an example only and does not fit a final product. You need to analyze
* how your product is supposed to react in case of Assert.
* @warning On assert from the SoftDevice, the system can only recover on reset.
*
* @param[in] line_num Line number of the failing ASSERT call.
* @param[in] file_name File name of the failing ASSERT call.
*/
void assert_nrf_callback(uint16_t line_num, const uint8_t * p_file_name)
{
app_error_handler(DEAD_BEEF, line_num, p_file_name);
}

/**@brief Function for initializing the Advertising functionality.
*
* @details Encodes the required advertising data and passes it to the stack.
* Also builds a structure to be passed to the stack when starting advertising.
*/
static void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED;

ble_advdata_manuf_data_t manuf_specific_data;

manuf_specific_data.company_identifier = APP_COMPANY_IDENTIFIER;

#if defined(USE_UICR_FOR_MAJ_MIN_VALUES)
// If USE_UICR_FOR_MAJ_MIN_VALUES is defined, the major and minor values will be read from the
// UICR instead of using the default values. The major and minor values obtained from the UICR
// are encoded into advertising data in big endian order (MSB First).
// To set the UICR used by this example to a desired value, write to the address 0x10001080
// using the nrfjprog tool. The command to be used is as follows.
// nrfjprog --snr <Segger-chip-Serial-Number> --memwr 0x10001080 --val <your major/minor value>
// For example, for a major value and minor value of 0xabcd and 0x0102 respectively, the
// the following command should be used.
// nrfjprog --snr <Segger-chip-Serial-Number> --memwr 0x10001080 --val 0xabcd0102
uint16_t major_value = ((*(uint32_t *)UICR_ADDRESS) & 0xFFFF0000) >> 16;
uint16_t minor_value = ((*(uint32_t *)UICR_ADDRESS) & 0x0000FFFF);

uint8_t index = MAJ_VAL_OFFSET_IN_BEACON_INFO;

m_beacon_info[index++] = MSB_16(major_value);
m_beacon_info[index++] = LSB_16(major_value);

m_beacon_info[index++] = MSB_16(minor_value);
m_beacon_info[index++] = LSB_16(minor_value);
#endif

manuf_specific_data.data.p_data = (uint8_t *) m_beacon_info;
manuf_specific_data.data.size = APP_BEACON_INFO_LENGTH;

// Build and set advertising data.
memset(&advdata, 0, sizeof(advdata));

advdata.name_type = BLE_ADVDATA_NO_NAME;
advdata.flags = flags;
advdata.p_manuf_specific_data = &manuf_specific_data;

err_code = ble_advdata_set(&advdata, NULL);
APP_ERROR_CHECK(err_code);

// Initialize advertising parameters (used when starting advertising).
memset(&m_adv_params, 0, sizeof(m_adv_params));

m_adv_params.type = BLE_GAP_ADV_TYPE_ADV_NONCONN_IND;
m_adv_params.p_peer_addr = NULL; // Undirected advertisement.
m_adv_params.fp = BLE_GAP_ADV_FP_ANY;
m_adv_params.interval = NON_CONNECTABLE_ADV_INTERVAL;
m_adv_params.timeout = APP_CFG_NON_CONN_ADV_TIMEOUT;
}

/**@brief Function for starting advertising.
*/
static void advertising_start(void)
{
uint32_t err_code;

err_code = sd_ble_gap_adv_start(&m_adv_params);
APP_ERROR_CHECK(err_code);

err_code = bsp_indication_set(BSP_INDICATE_ADVERTISING);
APP_ERROR_CHECK(err_code);
}

/**@brief Function for initializing the BLE stack.
*
* @details Initializes the SoftDevice and the BLE event interrupt.
*/
static void ble_stack_init(void)
{
uint32_t err_code;

nrf_clock_lf_cfg_t clock_lf_cfg = NRF_CLOCK_LFCLKSRC;

// Initialize the SoftDevice handler module.
SOFTDEVICE_HANDLER_INIT(&clock_lf_cfg, NULL);

ble_enable_params_t ble_enable_params;
err_code = softdevice_enable_get_default_config(CENTRAL_LINK_COUNT,
PERIPHERAL_LINK_COUNT,
&ble_enable_params);
APP_ERROR_CHECK(err_code);

//Check the ram settings against the used number of links
CHECK_RAM_START_ADDR(CENTRAL_LINK_COUNT,PERIPHERAL_LINK_COUNT);

// Enable BLE stack.
err_code = softdevice_enable(&ble_enable_params);
APP_ERROR_CHECK(err_code);
}

/**@brief Function for doing power management.
*/
static void power_manage(void)
{

uint32_t err_code = sd_app_evt_wait();
APP_ERROR_CHECK(err_code);

}

void in_pin_handler(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
//nrf_drv_gpiote_out_toggle(21);
nrf_gpio_pin_toggle(24);
advertising_start();
}

static void gpio_init(void)
{
nrf_gpio_cfg_input(17,NRF_GPIO_PIN_PULLUP);
nrf_gpio_cfg_input(19,NRF_GPIO_PIN_PULLUP);
nrf_gpio_cfg_output(24);

ret_code_t err_code;

err_code = nrf_drv_gpiote_init();
APP_ERROR_CHECK(err_code);

nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_HITOLO(true);
in_config.pull = NRF_GPIO_PIN_PULLUP;

err_code = nrf_drv_gpiote_in_init(18, &in_config, in_pin_handler);
APP_ERROR_CHECK(err_code);

nrf_drv_gpiote_in_event_enable(18, true);

}
uint8_t switch_hit(void)
{
static uint8_t prev_state = 1;
uint8_t cur_state;

// cur_state = nrf_gpio_pin_read(17);
cur_state = nrf_gpio_pin_read(17);
if(prev_state != cur_state)
{
prev_state = cur_state;
if(!cur_state)
return 1;
else
return 0;
}
else
return 0;
}
uint8_t switch_hit1(void)
{
static uint8_t prev_state = 1;
uint8_t cur_state;

// cur_state = nrf_gpio_pin_read(17);
cur_state = nrf_gpio_pin_read(19);
if(prev_state != cur_state)
{
prev_state = cur_state;
if(!cur_state)
return 1;
else
return 0;
}
else
return 0;
}

/**
* @brief Function for application main entry.
*/
int main(void)
{
uint32_t err_code;
// Initialize.
err_code = NRF_LOG_INIT(NULL);
APP_ERROR_CHECK(err_code);

APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, false);
// err_code = bsp_init(BSP_INIT_LED, APP_TIMER_TICKS(100, APP_TIMER_PRESCALER), NULL);
// APP_ERROR_CHECK(err_code);
ble_stack_init();
advertising_init();

// Start execution.
NRF_LOG_INFO("BLE Beacon started\r\n");
gpio_init();
advertising_start();
err_code = sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE);
APP_ERROR_CHECK(err_code);
err_code = sd_power_mode_set(NRF_POWER_MODE_LOWPWR);
APP_ERROR_CHECK(err_code);
// Enter main loop.
for (;; )
{
//power_manage();
if (NRF_LOG_PROCESS() == false)
{
//power_manage();
}
if(switch_hit())
{
//NRF_POWER->SYSTEMOFF = 1;
// sd_power_system_off();



sd_ble_gap_adv_stop();
power_manage();

}
if(switch_hit1())
{
nrf_gpio_pin_toggle(24);
}

}
}

/**
* @}
*/

I added gpio related code to the beacon example