Thingy52 DFU MESH

[Sunil vignesh]

Hi, I am interested to learn THINGY 52 working

I want to know how does the Thingy52 works?. any tutorial to explain the function of THINGY52

How to delete the boot loader and start work as a normal nRF52832 functions.

and How to return back into the DFU boot loader program and start work as it is

is there a procedure and zip file for doing this work.

and i need to work MESH in nordic thingy 52.

where i will get the mesh function for this thingy52.

[Einar Thorsrud]

Hi,

The standard Thingy:52 firmware does not support mesh, but there are Thingy:52 mesh demos.This is just an old demo, though.

If you want to understand BLE mash and DFU, you should look at the Mesh SDK documentation.

[Sunil vignesh]

Hi Einar,

thanks for you fast reply.

i have seen this video. https://www.youtube.com/watch?v=wa_ARkZSr_U

is this mesh demo works as like this.

shall i know how to upload this mesh code to thingy.

for my understand:

1. if i am going to connect the thingy board to nRFgo studio. and give erase all means it will delete the boot loader also or only the application and soft device.

2. if i delete the boot loader in the sense how to return back to thingy firmware. how to add boot loader to the thingy.

because. I am new to this nRF. can you please guide to do this.

[Einar Thorsrud]

Hi,

1. No. nRFgo studio is legacy software and should not be used.

2. Then you need to program it via SWD. It has no onboard debugger, but you can use for instance a nRF52 DK, where you connect a cable from the debug out port in the upper left corner of the DK to the debug connector on the thingy.

You can find instructions for the thingy mesh demo here. This demo does not demonstrate DFU, though.

[Sunil vignesh]

i am using segger embedded. is possible to program the THINGY board.using segger or any other IDE.?

is there any tutorial to upload boot loader to board.?

i found some Downloadable files in Thingy page https://www.nordicsemi.com/Software-and-Tools/Development-Kits/Nordic-Thingy-52/Download#infotabs

shall i know what that .zip file shows.

and what is the .hex file? . if i download the .hex file to thingy board through nRF5 DK. it will have boot loader.

or OTA concept will be done separately before the .HEX file upload?

[Einar Thorsrud]

Hi,

Most of these questions are beginner questions, and therefore I strongly advice that you start of with the nRF52840 DK instead, as the Thingy:52 is not a development kit. It does not have an onboard debugger, and it is not supported out of the box in the Mesh SDK. I can almost guarantee that you will save time (and thus money) on using the DK to begin with.

Sunil vignesh said:

is there any tutorial to upload boot loader to board.?

i found some Downloadable files in Thingy page https://www.nordicsemi.com/Software-and-Tools/Development-Kits/Nordic-Thingy-52/Download#infotabs

The thingy firmware comes with DFU, but this is not mesh. Mesh DFU is very different from normal DFU, so it does not really make much sense to look at what is allready there. Instead, you should familiarize yourself with the Mesh SDK, and not think som much about the Thingy to begin with (think of it as just another board you can run BLE mesh on, like any other custom board). And when you work with custom boards, always start with the DK, since this is a known good platform with tested examples in the Mesh SDK.

Sunil vignesh said:

shall i know what that .zip file shows.

and what is the .hex file? . if i download the .hex file to thingy board through nRF5 DK. it will have boot loader.

or OTA concept will be done separately before the .HEX file upload?

 I do not understand the question here. But again: please start with the DK, that will give you less unknowns in the beginning, since you actually have a known good starting point.